Flywheel Housing - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7573     | Link Bracket     | 2     |
Start By:
- Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Support the engine on a flat level surface forward of the flywheel housing.
- Attach Tool (A) and a suitable lifting device to flywheel housing (2) .
Show/hide table
Illustration 1 | g00823577 |
- Remove bolts (1) from the flywheel housing.
- Remove flywheel housing (2) from the engine. It may be necessary to hit flywheel housing (2) with a soft faced hammer in order to slide the flywheel housing off the dowels.
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7573     | Link Bracket     | 2     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Make sure that the rear face of the cylinder block and the faces of the flywheel housing are clean and free from damage.
- Attach Tool (A) and a suitable lifting device to flywheel housing (2) .
Show/hide table
Illustration 2 | g00823577 |
- Put flywheel housing (2) in position on the cylinder block. The dowels in the cylinder block must be aligned with the dowel holes in the flywheel housing.
- Install bolts (1) and tighten the bolts evenly to a torque of 78 N·m (58 lb ft).
- Remove the lifting device and Tool (A) from the engine.
End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Caterpillar Information System:
3176B Industrial Engine Sensors and Electrical Components
3612 and 3616 Engines Prelube Pump
3612 and 3616 Engines Prelube Pump
G3500 Engines Cylinder Liner - Install
797 Off-Highway Truck Power Train Differential and Bevel Gear
3034 Engine for Caterpillar Built Machines Flywheel - Install
3406E Generator Set Engines Information Plate
Electronic Modular Control Panel II+ (EMCP II+) for EUI Engines Troubleshooting Dedicated Shutdown Indicators
3034 Engine for Caterpillar Built Machines Flywheel - Remove
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
3176C and 3196 Engines for Caterpillar Built Machines Aftercooler - Test
3408E and 3412E Engines for Caterpillar Built Machines Exhaust Temperature - Test
Generator Set Control Panel for Switchgear Conversion Modes of Operation
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Final Drive
584 and 584HD Forwarders Work Tools
CIPI UNDERCARRIAGE Arrangements: 9Q5221, 9Q5234, 9Q5243, 9Q5245, 9Q5246, 9Q5247, 9Q5385, 9Q5433, 9Q5482, 9Q5622, 9Q5661, 9Q5719, 9Q5720, 9Q5721, 9Q5722, 9Q5830, 9Q5840, 9Q5857, 9Q5874, 9Q5883, 9Q5930 and 9Q5940 Final Drive
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Install
G3500 Engines Camshaft Bearings - Remove
G3500 Engines Camshaft Bearings - Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter and Water Separator
Alignment Procedure for G3500 Tandem Generator Sets{4450} Alignment Procedure for G3500 Tandem Generator Sets{4450}
784C and 785C Off-Highway Trucks Machine Systems Duo-Cone Seals - Install
3034 Engine for Caterpillar Built Machines Glow Plugs - Remove and Install
3412E, C30 and C32 Marine Engines Flywheel Housing - Remove and Install