Aftercooler - Remove
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
注: 后冷器有几种可能的配置。 以下程序演示了典型示例。
注: 在 3408E 发动机上执行以下程序。 但是, 3412E 发动机的过程非常相似。
- 将后冷器芯和水管中的冷却液排放到适当的容器中以便储存或处理。
Show/hide table
图 1 g00579401 典型示例 - 拆下螺栓 (5)、垫圈和隔套。
- 从夹子上拆下螺栓 (2) 和垫圈。
- 断开燃油管 (1)。 立即在全部阳接头上加装保护盖,在所有阴接头上加装螺塞。
- 拆下螺栓 (3 )。 拆下弯头 (4)。
Show/hide table
图 2 g00579403 典型示例 - 断开燃油管 (8)。 立即在全部阳接头上加装保护盖,在所有阴接头上加装螺塞。
- 拆下螺栓 (7)。 拆下安全阀壳体 (6)。
Show/hide table
图 3 g00579404 典型示例 - 拆下螺栓 (9)。 拆下弯头 (10) 和 O 形密封圈。
- 拆下螺栓 (13) 和垫圈。
- 拆下夹子 (12) 和支架 (11)。
- 拆下后冷器端盖 (14) 和密封垫。
Show/hide table
图 4 g00579407 典型示例 - 拆卸螺栓 (15) 和垫圈。
Show/hide table
图 5 g00579409 典型示例 - 拆下螺栓 (20)、弯头 (19) 和 O 形密封圈。
- 拆下两个过渡接头 (16) 和 O 形密封圈 (17)。
- 拆下两个过渡接头 (18) 和 O 形密封圈。
Show/hide table
图 6 g00579412 典型示例 - 将适当的起吊设备固定到后冷器芯 (21) 的起重支架上。
- 将后冷器芯从壳体上拆下。
后冷器芯的重量约为
26 kg (57 lb) 。 - 拆下 O 形密封圈 (22)。
Show/hide table
图 7 g00579413 典型示例 - 必要时,拆下螺栓 (24) 和垫圈。 拆下后冷器壳体 (23)。
Show/hide table
图 8 g00579418 典型示例 - 拆下后冷器壳体的密封垫 (25)。
Caterpillar Information System:
3126B Marine Engine General Information
3126B Marine Engine Engine Design
3612 and 3616 Engines Exhaust Manifold
3034 Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
3412E, C30 and C32 Marine Engines Flywheel Housing - Remove and Install
3034 Engine for Caterpillar Built Machines Glow Plugs - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Duo-Cone Seals - Install
Alignment Procedure for G3500 Tandem Generator Sets{4450} Alignment Procedure for G3500 Tandem Generator Sets{4450}
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter and Water Separator
G3500 Engines Camshaft Bearings - Install
G3500 Engines Camshaft Bearings - Remove
3408E and 3412E Engines for Caterpillar Built Machines Water Pump - Install
3412E, C30 and C32 Marine Engines Engine Control Module - Remove and Install
3176B Industrial Engine Refill Capacities
3176B Marine Engine Sensors and Electrical Components
3408E and 3412E Engines for Caterpillar Built Machines Aftercooler - Install
3034 Engine for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
G3500 Engines Turbocharger - Remove
3054 and 3056 Industrial and Generator Set Engines Air Inlet and Exhaust System
3412E, C30 and C32 Marine Engines Fuel Filter and Water Separator - Remove and Install
Wiring Harness Recommendations For 3500B Locomotive Engines{1408} Wiring Harness Recommendations For 3500B Locomotive Engines{1408}
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter (Primary)
365B Excavator Hydraulic System Oil (If Equipped with Fine Filtration Filter) - Change
3406E On-Highway Engine Camshaft Gear - Remove and Install