General Information
Show/hide table
图 1 | g00741036 |
Caterpillar 监控系统 |
Show/hide table
图 2 | g00296905 |
Caterpillar 监控系统显示器部件 (1) 四表组模块。 ( 2) 速度表/转速表组件。 ( 3) 主显示模块。 (4) 警告指示器。 ( 5) 仪表。 (6) 转速表。 ( 7) 速度读数区。 (8) 档位读数。 ( 9) 显示区。 |
Show/hide table
图 3 | g00741086 |
Caterpillar 监控系统显示器部件 (1) 四表组模块。 ( 2) 灯/档位模块。 (3) 报警指示灯。 ( 4) 主显示模块。 (5) 报警指示灯。 ( 6) 仪表。 (7) 模式指示灯。 ( 8) 转速计/档位显示。 ( 9) 显示区。 |
Caterpillar 监控系统是一个连续监测机器各个系统的电子监控系统。 这是一个包括以下设备的模块化监控系统: 主显示模块 , 各种开关和传感器 , 行动灯 , 行动警报, 车速/转速计模块 , 灯/档位模块 和 四仪表组模块 。
主显示模块是系统的大脑。 本模块从开关、传感器和其他电子控件接收信息。 通过 CAT 数据链路传输这些信息。 主显示模块处理所有信息。 主要显示模块将为下面的显示激活各种输出:
- 主显示模块的显示区域
- 四仪表组模块
- 速度表/转速计模块
- 灯/档位模块
- 行动灯
- 行动警报
显示部件显示机器系统的状况。 操作员还可以获得系统诊断信息。
构成 Caterpillar 监控系统的三个模块具有以下特点:
- 十个报警指示灯 ( 4) 用于显示机器的异常状况。
- 提供一个六位数字显示区 ( 9)。 显示区显示以下模式: 机器工作小时数(工时计) , 发动机转速(转速表) , 机器行驶里程(里程表) 和 诊断代码 。 显示器上可显示车速/转速计模块和四仪表组模块的信息。 显示区有七个单位指示灯和一个维修指示灯。 操作员选择在显示区域中显示的系统信息。
- 显示区中可以显示九种不同的单位指示灯。 可显示的装置指示灯是 "°C"、"kPa"、"MILES"、"KM"、"RPM"、"LITERS" 和 "HOURMETER" 符号。 这些指示灯显示六位数字显示区上测量数据的单位。 指示灯的点亮(ON) 和熄灭(OFF)与六位数字显示区上的信息相对应。
- 为了显示当前的故障,使用了一个维修代码指示器。 维修代码指示器用在维修模式及诊断滚动模式中。
- 一个转速表 (6) 显示发动机转速信息(RPM)。
- 一个三位数字显示区 ( 7) 显示行驶速度信息。 显示速度的单位是 "MPH" 和 "km/h"。
- 两位数字档位读出器 ( 8) 上显示变速箱档位和方向信息。
- 五个报警指示灯用于显示机器的异常状况。
- 五个模式指示灯显示当前已激活的动力传动系功能。
- 转速计/档位显示的前四位数字显示引擎 rpm。 转速计/档位显示的最后两位数字显示档位和方向。
- 四个电子仪表 (5) 显示机器的状况。 以下是典型的状况: 发动机冷却液温度 , 变速箱油温度 , 液压油温度 和 燃油油位。
不同的机器会有不同的状况。 外部行动灯和行动警报会指示故障的严重程度(警告级别)。
Caterpillar Information System:
784C and 785C Off-Highway Trucks Machine Systems Steering Tank and Filter - Install
769D Off-Highway Truck and 771D Quarry Truck Heating and Air Conditioning Control
583R Pipelayer Engine Supplement Hood and Dust Ejector - Remove and Install
583R Pipelayer Engine Supplement Electric Starting Motor - Remove and Install
784C, 785C and 785C HAA Off-Highway Truck/Tractors Hydraulic System Control Valve (Pulled Unit)
784C and 785C Off-Highway Trucks Machine Systems Steering Tank and Filter - Assemble
550, 570 and 580 Wheel Harvesters Backup Alarm
24H Motor Grader Hydraulic and Steering System Position Sensor (Ripper)
583R Pipelayer Engine Supplement Alternator - Remove and Install
583R Pipelayer Power Train Duo-Cone Conventional Seals - Install
784C, 785C and 785C HAA Off-Highway Truck/Tractors Hydraulic System Control Valve (Hoist)
24H Motor Grader Hydraulic and Steering System Position Sensor (Articulation)
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Bank Valve - Disassemble
3306B Industrial Engine Starting the Engine
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Air Control Valve (Service Brake)
784C and 785C Off-Highway Trucks Machine Systems Check Valve (Primary Air Tank) - Remove and Install
C-10 and C-12 Industrial Engines Inlet Air Temperature Sensor
583R Pipelayer Power Train Duo-Cone Inverted Seals - Install
3406C Engines for Caterpillar Built Machines Fuel Injection Pump
583R Pipelayer Engine Supplement Muffler - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0444 FMI 05 Magnetic Switch (Start Relay) Current Below Normal - Test
583R Pipelayer Engine Supplement Air Cleaner - Remove and Install
784C, 785C and 785C HAA Off-Highway Truck/Tractors Hydraulic System Body Mounting
550, 570 and 580 Wheel Harvesters Final Drive Oil Level - Check