Hook Load Line - Install
Show/hide table
Do not use a wire rope cable that is kinked, frayed or has worn spots. Wear gloves when handling the wire rope cable. |
Show/hide table
NOTICE |
---|
Use 6 X 25 filler wire, right regular lay, independent wire rope core, pre-formed, improved plow steel-type cables. |
Show/hide table
Specifications     | ||
---|---|---|
Cable     | Diameter     | Length     |
Hook Load Line     | 19.05 mm (.75 inch)     |
50.3 m (165 feet)     |
Weld the ends of the cable in order to prevent fraying.
- Lower the boom to the horizontal position.
- Unwind the cable.
- Disconnect the cable from the load drum.
- Unroll the new cable from the spool.
Show/hide table
NOTICE |
---|
Unroll the wire rope cable from the spool. Never lift the wire rope off the spool in coils. |
- Install the cable to the winch drum for the hook load line. Insert the end of the cable downward through the slot in the drum. Form a loop and insert the cable end upward through the slot. Insert the wedge into the loop in the cable. Pull the cable in order to seat the wedge and the cable in the pocket.
Show/hide table
Illustration 1 | g00430679 |
The winch drum for the hook load line is located below the winch drum for the boom. The winch drum for the hook load line does not show in the photo illustration. |
- Wind one half of the cable evenly across the load drum.
- Install the hook load line from the winch drum onto the sheave blocks. Position the cable over upper sheave (1) , under lower sheave (2) , over upper sheave (3) , and under lower sheave (4) .
Show/hide table
Illustration 2 | g00429258 |
- Insert the cable into the pocket and around wedge (5) .
Show/hide table
Illustration 3 | g00429358 |
- Insert the cable end through clamp (6) . Tighten the nuts on the clamp.
Note: The cable should go over upper sheave (1) toward the front of the machine. Anchor the cable toward the rear of the machine.
Caterpillar Information System:
DASA 280 Measuring and Control System Programming Variables
793C Off-Highway Truck Machine Systems Double Check Valve (Rear Air over Hydraulic Cylinder) - Remove and Install
793C Off-Highway Truck Machine Systems Double Check Valve (Front Air over Hydraulic Cylinder) - Remove and Install
793C Off-Highway Truck Machine Systems Double Check Valve - Assemble
793C Off-Highway Truck Machine Systems Double Check Valve - Disassemble
793B Off-Highway Truck Steering System Solenoid Valve (Steering)
793C Off-Highway Truck Machine Systems Double Check Valve (Service and Secondary Brake) - Remove and Install
3126E and 3126B Commercial and Truck Engines Belt Tensioner - Inspect - If Equipped
793C Off-Highway Truck Machine Systems Double Check Valve (Retarder Control) - Remove and Install
3034 Engine for Caterpillar Built Machines Flywheel
527 Track-Type Skidder Power Train Resonator
527 Track-Type Skidder Power Train Track Idler
3176C and 3196 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO)
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Nozzles
DASA 280 Measuring and Control System Setting Module
572R Pipelayer Boom Line - Install
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Coupler Cylinder - Remove
793C Off-Highway Truck Machine Systems Hoist and Brake Hydraulic Breather - Remove and Install
784C and 785C Off-Highway Truck/Tractors Steering System Oil Filter - Replace
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Pump
793C Off-Highway Truck Machine Systems Brake Light Pressure Switch - Remove and Install
DASA 280 Measuring and Control System Programming Times
784C and 785C Off-Highway Truck/Tractors Ether Starting Aid Cylinder - Replace
3126E and 3126B Commercial and Truck Engines Fuel System - Prime