1998/11/16 Caterpillar


New Hoist And Brake Cooling Pumps Are Now Available For Certain Off-Highway Trucks{5083}

Usage:


789 (9ZC),
789B (7EK) Off-Highway Trucks

SUPPLEMENT: DECEMBER 14, 1998

Service Magazine SEPD0444, Article 15, Page 19, November 16, 1998; "New Hoist And Brake Cooling Pumps Are Now Available For Certain Off-Highway Trucks ".

Disregard this article. A Service Magazine Article with correct information will be published at a later date.

--------------- END SUPPLEMENT ---------------

Description of Change: The new cast iron pumps will allow the hoist system pressure to be increased and will improve the service life of both pumps . The parts listed below must be ordered and installed together to produce the desired results.

Following the installation of the above parts, the hoist relief pressure can be adjusted to 2750 psi max by using the adjustment procedure in the 789 or 789C Service manual.

NOTE: Do not increase the hoist relief pressure to 2750 psi suing the 5T-3229 Pump Group. Adaptable To:

Adaptable To: 789 (9ZC1-Up)and 789B (7EK1-Up)

Caterpillar Information System:

1998/11/16 New Clutch Discs With Improved Core Material Now Available For Large Off-Highway Trucks{3187,3030}
1998/11/16 Certain Off-Highway Trucks Shipping With Dry Batteries{1401}
1998/11/16 Torque Converter Lockup Clutch Rebuild{3100,3102,3136}
1998/11/16 Retaining Ring Service Kit Available For Accumulators{5077,4263}
1998/11/16 New Head For Dozer Tilt Cylinders And Change To Head For Ripper Lift Cylinder Assure Oil Flow Through Bypass In Piston. Torque Increased For Piston Nut In Dozer Tilt Cylinders{5102,5104}
1998/11/09 Stanadyne Fuel Injection Pumps Now Equipped With Tamper Resistant Fittings {1251}
1998/11/09 Orifices Removed In Propel Pump EDCs {3205}
1998/11/09 Wiring Schematic For Telehandlers {7566}
1998/11/09 Improved VIMS 100-3055 And 118-7226 Temperature Sensor Groups Now Used {7601,1408}
1998/11/09 Improved Final Drive Wheel Bearing Retainer Plate Available For Certain Off-Highway Trucks {4051,4066,4208}
1998/11/09 New Aftercooler Tube Is Available To Move Sensor Away From Exhaust Heat. {1380,1063}
1998/11/09 Turbocharger Exhaust Tubes Now Boxed To Prevent Water Accumulation In Turbocharger During Shipment {1061,1062}
1998/11/16 New Manifold In Hoist Lines Eliminates False Actuation Of VIMS (Vital Information Monitoring System){7601}
1998/11/16 Lubrication And Maintenance Literature Available{0374,0375}
1998/11/16 Special Instruction, REHS0316, "Troubleshooting Guide For Engine Prelub System" Available{0374,1319,1469}
1998/11/16 Hydraulic Electronic Control Now Serviceable{5702}
1998/11/16 Correction To Testing And Adjusting Manual, RENR3005{0374,5069,5069}
1998/11/16 Improved Throttle Cables Available For Utility Compactors{1265}
1998/11/16 Margin Pressure Increased For Piston And Vane Pump Group In Steering System{5070,4306}
1998/11/16 Auger Mounting Bolt Change{5620,5326}
1998/11/16 Compensator And Socket Head Bolts For 3408E And 3412E Hydraulically Actuated Electronically Controlled Unit Injector (HEUI) Hydraulic Pump Now Available{1714}
1998/11/16 Revised Special Instruction, REHS0126-02, "Caterpillar Electronic Controls Service Code Information Description List", Available{0374,1901,1927,1930,1948,3168,4348,4802,4808,4810,4812,5511,5701,7490,7494,7601,7602,7610}
1998/11/23 Main Drive Shaft Slip Spline Lubrication Interval Changed {3253}
1998/11/23 Be Sure To Use Correct Stub Shaft When Replacing Cam Idler Gear {1234,1212}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.