1996/11/11 Caterpillar


Special Instruction, SEHS9874-01, "Challenger Agricultural Tractors In Scraper Applications"{0375,0376,4150,7000}

Usage:


Challenger 35 (8DN),
Challenger 45 (1DR),
Challenger 55 (7DM),
Challenger 65 &
65B (7YC),
Challenger 65C, 65D (2ZJ),
Challenger 70C (2YL),
Challenger 75 (4CJ),
Challenger 75C (4KK),
Challenger 75D (5AR),
Challenger 85C (9TK),
Challenger 85D (4GR) Agricultural Tractors

Challenger Agricultural Tractors can do a credible job in scraper applications when used by a trained operator in the right conditions.

Special Instruction, SEHS9874-01, "Challenger Agricultural Tractors in Scraper Applications", provides dealers and end users information about tractor setup (configuration), scraper setup, allowable weight transfer, and operating tips and techniques when using Challenger Agricultural Tractors in scraper applications. This information will help improve performance and reduce costs and problems inherent in the application of an agricultural tractor with scrapers.

Special Instruction, SEHS9874-01, "Challenger Agricultural Tractors in Scraper Applications", is available through normal literature channels.

Caterpillar Information System:

1996/11/04 Fuel Injection Pump Bushings Have New Groove Adjacent To Load Ring {1251}
1996/11/04 Adjustment Procedure For Cab Door Latch And Hold-Open Release {7301,7308}
1996/11/04 New Suspension Frame Group Now Used To Prevent Cracking {7216,7203}
1996/11/04 Improper Monitoring Of DIFFERENTIAL OIL LEVEL By Vital Information Management System (VIMS) {3258,1920,7601}
1996/11/04 New Tooling Available To Install Power Take-off Output Shaft And Hitch Rock Shaft Seals {0745,3107,0755,7117}
1996/10/28 New Procedure For Installing The Gear On Scavenge Oil Pump Shafts Within Scavenge Oil Pump Groups {1312}
1996/10/28 Seal Kits For Hydraulic Unit Injector Pump Groups Available {1250,1714}
1996/10/28 Procedure To Assemble Hydraulic Pilot Line Fittings {5057}
1996/10/28 Boom And Attachment Control Must Be In The "HOLD" Position When Starting The Engine {5725,7400}
1996/10/28 Additional Brake System Servicing Information {4005}
1996/10/28 Procedure To Adjust Creeper Speed Control {3162}
1996/10/28 Special Instruction SEHS9953 Available for Procedure to Repair Dump Body Pivot Assemblies {7258}
1996/11/11 Improved Electronic Control Modules Reduce Electrical Interference{7490,3175}
1996/11/11 Longer Battery Cable Now Used To Prevent Interference With Starting Motor Cover{1401}
1996/11/11 Special Instructions SEHS9896, REHS0037 And REHS0038 Available For Installation Of A Bolt-On Ball On Early Drawbars{6153,6157,6170,6171}
1996/11/11 New Material Increases Service Life Of Brake Hubs{4215,4208,4201}
1996/11/11 Hydraulic Oil Additive Used That Eliminates Noise In Differentials {3263}
1996/11/11 New Crankcase Guard Provides Increased Resistance To Damage{7151}
1996/11/11 New Cover Plates For Rear Of Headlight Guards Protect Wiring From Damage{7182}
1996/11/11 Foot Rest Has Been Added To Improve Operator Comfort{7301,7265}
1996/11/11 Incorrect Electronic Control Service Codes Film{1901}
1996/11/11 Follow Correct Maintenance Procedure To Extend Drum Drive Gear Reducer Service Life{5655}
1996/11/11 Service Replacements For Discontinued Piston Pump Groups{5070}
1996/11/11 New Threaded Gland Cylinder Heads Have Stronger Seal Land{7562,4303,5102,5104,5105,5223,5229,5265,5452}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.