Procedure To Adjust Creeper Speed Control {3162}
Usage:
914G (7ZM, 9WM) Wheel Loaders;
IT14G (8ZM, 1WN) Integrated Toolcarriers
The procedure to adjust the creeper speed control group is not included in the Service Manual for the above machines. For machines equipped with this attachment, use the following procedure to adjust the creeper speed control.
Procedure
1. Remove lever (1) from shaft (3).
2. Rotate shaft (3) fully clockwise until there is contact with the stop pins.
3. Without rotating shaft (3), install and adjust creeper lever (1) until it contacts limit switch (2). Make sure that the lever does not actuate the limit switch.
4. Tighten bolt (5).
5. Rotate lever (1) clockwise and check actuation of limit switch (2).
Caterpillar Information System:
1996/10/28 Special Instruction SEHS9953 Available for Procedure to Repair Dump Body Pivot Assemblies {7258}
1996/10/28 Special Instruction SEHS9952 Available for Procedure to Repair Dump Body Pivot Assemblies {7258}
1996/10/28 Modifications To Body Guide Prevent Interference {7258}
1996/10/28 New Race Used in Steering Groups to Improve Angular Rotation of Sockets {4305}
1996/10/28 Parts Added to Increase Clearance Between Steering Relief Valve Group and Engine Oil Pan Assembly {4304,4307}
1996/10/28 Higher Viscosity Power Train Oil Should Be Used in Certain Applications {4070,0645}
1996/10/28 New Flange And Seal Can Be Used In Engine Turbocharger Groups To Help Prevent Exhaust Leaks {1052,1059}
1996/10/28 Cab Door Hold Back Latch Modifications Improve Door Retention {7308,7325}
1996/10/28 Front Idler Hub Oil Change Interval And Factory Oil Fill Changed {4159,4167,4215}
1996/10/28 Improved Final Drive Pinion Bearing Setting Procedure Used And New Shim Pack Kit Available {4050,4091}
1996/10/21 New O-Ring Seals Used On "Through-Head-Adapter" And "Internal Fuel Lines" In Fuel Injection Lines Groups{1252}
1996/10/21 Proper Procedure For Servicing And Cleaning The Fuel Injection Pump{1251}
1996/10/28 Additional Brake System Servicing Information {4005}
1996/10/28 Boom And Attachment Control Must Be In The "HOLD" Position When Starting The Engine {5725,7400}
1996/10/28 Procedure To Assemble Hydraulic Pilot Line Fittings {5057}
1996/10/28 Seal Kits For Hydraulic Unit Injector Pump Groups Available {1250,1714}
1996/10/28 New Procedure For Installing The Gear On Scavenge Oil Pump Shafts Within Scavenge Oil Pump Groups {1312}
1996/11/04 New Tooling Available To Install Power Take-off Output Shaft And Hitch Rock Shaft Seals {0745,3107,0755,7117}
1996/11/04 Improper Monitoring Of DIFFERENTIAL OIL LEVEL By Vital Information Management System (VIMS) {3258,1920,7601}
1996/11/04 New Suspension Frame Group Now Used To Prevent Cracking {7216,7203}
1996/11/04 Adjustment Procedure For Cab Door Latch And Hold-Open Release {7301,7308}
1996/11/04 Fuel Injection Pump Bushings Have New Groove Adjacent To Load Ring {1251}
1996/11/11 Special Instruction, SEHS9874-01, "Challenger Agricultural Tractors In Scraper Applications"{0375,0376,4150,7000}
1996/11/11 Improved Electronic Control Modules Reduce Electrical Interference{7490,3175}