C280-16 Marine Engines Caterpillar


Ordering Replacement Parts

Usage:

C280-16 R4M

------ WARNING! ------

When replacement parts are required for this product Caterpillar recommends using Caterpillar replacement parts or parts with equivalent specifications including, but not limited to, physical dimensions, type, strength and material.

Failure to heed this warning can lead to premature failures, product damage, personal injury or death.


Quality Cat replacement parts are available from Cat dealers throughout the world. Cat dealer parts inventories are up-to-date. The parts stocks include all the parts that are normally needed to protect your Cat engine investment.

When you order parts, specify the following information:

  • Part number

  • Part name

  • Quantity

If there is a question concerning the part number, provide your dealer with a complete description of the needed item.

When a Cat engine requires maintenance and/or repair, provide the dealer with all the information that is stamped on the Information Plate. This information is described in this Operation and Maintenance Manual (Product Information Section).

Discuss the problem with the dealer. Inform the dealer about the conditions of the problem and the nature of the problem. Inform the dealer about when the problem occurs. This information will help the dealer in troubleshooting the problem and solving the problem faster.

Aftertreatment Replacement Parts

Table 1
Aftertreatment On-Board Replacement Parts(1) 
System  Quantity  Item 
CEM  DEF nozzle 
1 Pressure sensor 
1 Gasket assembly 
1 Exhaust gasket 
35 Pin assembly 
1 NOx sensor (Engine Output) 
1 NOx sensor (Exhaust Outlet) 
2 Temperature sensor 
Dosing cabinet (Marine Society Kit)  DEF pump group 
1 Regulator assembly 
2 O-ring seal 
1 O-ring seal 
1 Sender unit assembly (DEF fluid level) 
1 DEF pressure sensor 
1 Pressure sensor 
1 Temperature sensor 
1 Solenoid valve (24 VDC) (Air) 
1 Solenoid valve (24 VDC) (DEF Return) 
1 Solenoid valve (24 VDC) (Tank Fill 
(1) For more detailed information, refer to the applicable Parts Manual.

Caterpillar Information System:

New Oil Cooler Components Are Now Used for Certain G3500 Series Engines {1378} New Oil Cooler Components Are Now Used for Certain G3500 Series Engines {1378}
An Audible Knock Is Heard on Certain 3500 Dynamic Gas Blending Engines {1278, 1280, 1741} An Audible Knock Is Heard on Certain 3500 Dynamic Gas Blending Engines {1278, 1280, 1741}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Blade Operation
New Turbochargers are Now Used on Certain 3512C and 3516C Marine Engines {1052, 1053} New Turbochargers are Now Used on Certain 3512C and 3516C Marine Engines {1052, 1053}
C7.1 Marine Propulsion Engine Crankcase Breather - Install
C7.1 Marine Propulsion Engine Crankcase Breather - Remove
C175-20 Locomotive Engine Injector Solenoid - Test
3500E Marine Engines On-Board Replacement Parts
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Hydraulic Schematic (Hydraulic Fan)
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Piston Motor (Fan Drive)
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Stopping the Machine
Retrofitting for the Dynamic Gas Blending Capability on Certain 3516B Engines {1071, 1100, 1250, 1270, 1274, 1403, 1716, 1901, 1920} Retrofitting for the Dynamic Gas Blending Capability on Certain 3516B Engines {1071, 1100, 1250, 1270, 1274, 1403, 1716, 1901, 1920}
A New Electrical Starter Group and Solenoid Kit is Now Used for Certain G3304 and G3306 Engines {1453, 1467} A New Electrical Starter Group and Solenoid Kit is Now Used for Certain G3304 and G3306 Engines {1453, 1467}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Operator Controls
G3516 TA Engine Engine Timing Actuator - Test
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Pump Control
XQP1100 Generator Set Generator Operation
New Engine Software is Now Used for Certain C175 Locomotive Engines {1920} New Engine Software is Now Used for Certain C175 Locomotive Engines {1920}
New Instruction for Tightening Fuel Cooler Hose is Now Available for Certain C15 and C18 Engines {1353, 1712} New Instruction for Tightening Fuel Cooler Hose is Now Available for Certain C15 and C18 Engines {1353, 1712}
New Injector Hold Down Clamps Are Used for Certain C175 Locomotive Engines {1251, 1290} New Injector Hold Down Clamps Are Used for Certain C175 Locomotive Engines {1251, 1290}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Seat
Update on Plastic Plugs for Certain Cat® C13 and C15 Defra Base Generator Sets {1273} Update on Plastic Plugs for Certain Cat® C13 and C15 Defra Base Generator Sets {1273}
New Injector Jumper Harness is Now Available for Certain 3406E Truck Engines {1120, 1403} New Injector Jumper Harness is Now Available for Certain 3406E Truck Engines {1120, 1403}
New Engine Software Are Now Used for Certain C27 and C32 Engines {1920} New Engine Software Are Now Used for Certain C27 and C32 Engines {1920}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.