New Oil Cooler Components Are Now Used for Certain G3500 Series Engines {1378}
- Engine
- G3512E (S/N: SST1-102)
- G3516H (S/N: NWJ1-110; GLN1-138)
- G3520C (S/N: LGS1-198)
- G3520H (S/N: GFR1-199)
- G3516H (S/N: NWJ1-110; GLN1-138)
- Generator Set
- CG170-16 (S/N: KSJ1-165)
Description Of Change: The new hose assemblies and elbow adapter that are used help reduce stress from misalignment which prevents oil leaks.
By changing the rigid fluid piping to a flexible line and switching from a 45 degree angle elbow to a 90 degree elbow, stress is reduced in the fluid lines.
Adaptable To: The following changes are adaptable to the products within the listed serial numbers, and are effective with all products after the listed serial numbers.
Table 1 contains the parts for this change.
Show/hide table
| New Part Number | Part Name | Previous Part Number | Qty |
|---|---|---|---|
| Flared Elbow | 1 | ||
| Hose As | 1 | ||
| Hose As | 1 | ||
| Hose As | 1 |
Caterpillar Information System:
An Audible Knock Is Heard on Certain 3500 Dynamic Gas Blending Engines {1278, 1280, 1741} An Audible Knock Is Heard on Certain 3500 Dynamic Gas Blending Engines {1278, 1280, 1741}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Blade Operation
New Turbochargers are Now Used on Certain 3512C and 3516C Marine Engines {1052, 1053} New Turbochargers are Now Used on Certain 3512C and 3516C Marine Engines {1052, 1053}
C7.1 Marine Propulsion Engine Crankcase Breather - Install
C7.1 Marine Propulsion Engine Crankcase Breather - Remove
C175-20 Locomotive Engine Injector Solenoid - Test
3500E Marine Engines On-Board Replacement Parts
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Hydraulic Schematic (Hydraulic Fan)
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Piston Motor (Fan Drive)
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Stopping the Machine
Retrofitting for the Dynamic Gas Blending Capability on Certain 3516B Engines {1071, 1100, 1250, 1270, 1274, 1403, 1716, 1901, 1920} Retrofitting for the Dynamic Gas Blending Capability on Certain 3516B Engines {1071, 1100, 1250, 1270, 1274, 1403, 1716, 1901, 1920}
Selective Catalytic Reduction Retrofit Aftertreatment Diesel Particulate Filter - Remove and Install - If Equipped
C280-16 Marine Engines Ordering Replacement Parts
A New Electrical Starter Group and Solenoid Kit is Now Used for Certain G3304 and G3306 Engines {1453, 1467} A New Electrical Starter Group and Solenoid Kit is Now Used for Certain G3304 and G3306 Engines {1453, 1467}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Operator Controls
G3516 TA Engine Engine Timing Actuator - Test
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Pump Control
XQP1100 Generator Set Generator Operation
New Engine Software is Now Used for Certain C175 Locomotive Engines {1920} New Engine Software is Now Used for Certain C175 Locomotive Engines {1920}
New Instruction for Tightening Fuel Cooler Hose is Now Available for Certain C15 and C18 Engines {1353, 1712} New Instruction for Tightening Fuel Cooler Hose is Now Available for Certain C15 and C18 Engines {1353, 1712}
New Injector Hold Down Clamps Are Used for Certain C175 Locomotive Engines {1251, 1290} New Injector Hold Down Clamps Are Used for Certain C175 Locomotive Engines {1251, 1290}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Seat
Update on Plastic Plugs for Certain Cat® C13 and C15 Defra Base Generator Sets {1273} Update on Plastic Plugs for Certain Cat® C13 and C15 Defra Base Generator Sets {1273}
New Injector Jumper Harness is Now Available for Certain 3406E Truck Engines {1120, 1403} New Injector Jumper Harness is Now Available for Certain 3406E Truck Engines {1120, 1403}