Blade Operation
Show/hide table
FIGYELMEZTETÉS |
---|
A munkagép megrongálódhat, ha az állítható méretű járószerkezet és a tolólap nem egyforma szélességre vannak állítva (például egy ajtón való áthaladáskor). |
A tolólap szélességének csökkentése
- Emelje fel a tolólapot körülbelül
1-2 cm (0.39-0.79 inch) magasságra. - Húzza ki mindkét oldalon a rögzítőcsapokat (A).
Show/hide table
Illusztráció 2 g06262835 - Hajtsa be a tolólap toldatait (B) mindkét oldalon.
- Helyezze vissza a rögzítőcsapokat (A) mindkét oldalon.
Show/hide table
Illusztráció 1 | g06262829 |
A tolólap szélességének növelése
- Emelje fel a tolólapot körülbelül
1-2 cm (0.39-0.79 inch) magasságra. - Húzza ki mindkét oldalon a rögzítőcsapokat (A).
- Hajtsa ki a tolólap toldatait (B) mindkét oldalon.
Show/hide table
Illusztráció 4 g06262829 - Helyezze vissza a rögzítőcsapokat (A) mindkét oldalon.
Show/hide table
Illusztráció 3 | g06262836 |
Caterpillar Information System:
New Turbochargers are Now Used on Certain 3512C and 3516C Marine Engines {1052, 1053} New Turbochargers are Now Used on Certain 3512C and 3516C Marine Engines {1052, 1053}
C7.1 Marine Propulsion Engine Crankcase Breather - Install
C7.1 Marine Propulsion Engine Crankcase Breather - Remove
C175-20 Locomotive Engine Injector Solenoid - Test
3500E Marine Engines On-Board Replacement Parts
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Hydraulic Schematic (Hydraulic Fan)
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Piston Motor (Fan Drive)
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Stopping the Machine
Retrofitting for the Dynamic Gas Blending Capability on Certain 3516B Engines {1071, 1100, 1250, 1270, 1274, 1403, 1716, 1901, 1920} Retrofitting for the Dynamic Gas Blending Capability on Certain 3516B Engines {1071, 1100, 1250, 1270, 1274, 1403, 1716, 1901, 1920}
Selective Catalytic Reduction Retrofit Aftertreatment Diesel Particulate Filter - Remove and Install - If Equipped
C7.1 Marine Propulsion Engine Flywheel - Remove and Install
C7.1 Marine Propulsion Engine Electric Starting Motor - Remove and Install
An Audible Knock Is Heard on Certain 3500 Dynamic Gas Blending Engines {1278, 1280, 1741} An Audible Knock Is Heard on Certain 3500 Dynamic Gas Blending Engines {1278, 1280, 1741}
New Oil Cooler Components Are Now Used for Certain G3500 Series Engines {1378} New Oil Cooler Components Are Now Used for Certain G3500 Series Engines {1378}
C280-16 Marine Engines Ordering Replacement Parts
A New Electrical Starter Group and Solenoid Kit is Now Used for Certain G3304 and G3306 Engines {1453, 1467} A New Electrical Starter Group and Solenoid Kit is Now Used for Certain G3304 and G3306 Engines {1453, 1467}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Operator Controls
G3516 TA Engine Engine Timing Actuator - Test
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Pump Control
XQP1100 Generator Set Generator Operation
New Engine Software is Now Used for Certain C175 Locomotive Engines {1920} New Engine Software is Now Used for Certain C175 Locomotive Engines {1920}
New Instruction for Tightening Fuel Cooler Hose is Now Available for Certain C15 and C18 Engines {1353, 1712} New Instruction for Tightening Fuel Cooler Hose is Now Available for Certain C15 and C18 Engines {1353, 1712}
New Injector Hold Down Clamps Are Used for Certain C175 Locomotive Engines {1251, 1290} New Injector Hold Down Clamps Are Used for Certain C175 Locomotive Engines {1251, 1290}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Seat