Electric Starting Motor - Remove and Install
Reference: Special Instruction, "Visual Service Procedures - Colors and Symbols" , M0066576.
Show/hide table
 |
|
Accidental engine starting can cause injury or death to personnel working on the equipment. To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system. Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on. |
- The engine can start automatically. Ensure that the power supply is isolated before any service or repairs is performed.
- Turn the battery disconnect switch to the OFF position.
- Place identification marks on the harness assembly that is connected to the electric starting motor and the solenoid.
Show/hide table
| |
| Illustration 1 | g06262415 |
Show/hide table
| |
| Illustration 2 | g06262416 |
Show/hide table
| |
| Illustration 3 | g06262418 |
- Install the electric starting motor in the reverse order of removal.
Caterpillar Information System:
C7.1 Marine Propulsion Engine Auxiliary Water Pump - Assemble
C7.1 Marine Propulsion Engine Auxiliary Water Pump - Disassemble
Improved Camera is Now Used on Certain Cat® Products {1408} Improved Camera is Now Used on Certain Cat® Products {1408}
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Valve Mechanism Cover - Remove and Install
New Diesel Exhaust Fluid Pump Connector is Now Used on Certain C7.1 - C18 Engine Applications {108J} New Diesel Exhaust Fluid Pump Connector is Now Used on Certain C7.1 - C18 Engine Applications {108J}
3516C HD Generator Set with Gearbox General Hazard Information
C7.1 Marine Propulsion Engine Auxiliary Water Pump - Remove and Install
C7.1 Marine Propulsion Engine Transmission Oil Cooler - Remove and Install
C7.1 Marine Propulsion Engine Transmission Oil Temperature Sensor - Remove and Install
C7.1 Marine Propulsion Engine Transmission Oil Pressure Sensor - Remove and Install
793F Off-Highway Truck Engine Supplement Diesel Exhaust Fluid Filter - Remove and Install
3516C HD Generator Set with Gearbox Reference Information
C7.1 Marine Propulsion Engine Flywheel - Remove and Install
Selective Catalytic Reduction Retrofit Aftertreatment Diesel Particulate Filter - Remove and Install - If Equipped
Retrofitting for the Dynamic Gas Blending Capability on Certain 3516B Engines {1071, 1100, 1250, 1270, 1274, 1403, 1716, 1901, 1920} Retrofitting for the Dynamic Gas Blending Capability on Certain 3516B Engines {1071, 1100, 1250, 1270, 1274, 1403, 1716, 1901, 1920}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Stopping the Machine
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Piston Motor (Fan Drive)
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Hydraulic Schematic (Hydraulic Fan)
3500E Marine Engines On-Board Replacement Parts
C175-20 Locomotive Engine Injector Solenoid - Test
C7.1 Marine Propulsion Engine Crankcase Breather - Remove
C7.1 Marine Propulsion Engine Crankcase Breather - Install
New Turbochargers are Now Used on Certain 3512C and 3516C Marine Engines {1052, 1053} New Turbochargers are Now Used on Certain 3512C and 3516C Marine Engines {1052, 1053}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Blade Operation