Turbocharger - Install
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | - | Loctite 镍防咬合剂 | 1 |
| B | - | 磷酸盐处理 S-OT 40 橡胶润滑剂 | 1 |
Show/hide table
| 注意 |
|---|
|
卡箍组件应只使用一次。 使用后弃置所有卡箍组件。 |
- 将适当的起吊设备连接在涡轮增压器 (2) 上。 涡轮增压器 (2) 的重量大约为
143 kg (315 lb) 。 - 将工具 (A) 涂覆到螺栓 (1) 上，然后安装涡轮增压器 (2) 和螺栓 (1)。
Show/hide table
图 2 g06259633 - 安装管 (7) 和螺栓 (9)。
- 连接软管 (8)、软管 (6)，然后安装卡箍 (3)、 (4) 和 (5)。
- 将工具 (A) 涂覆到卡箍 (3) 的螺纹和内径上。 将卡箍 (3) 拧紧至扭矩为
20 ± 2 N·m (177 ± 18 lb in) 。 - 绕着圆周敲打卡箍 (3)，然后拧紧至扭矩为
20 ± 2 N·m (177 ± 18 lb in) 。 - 将工具 (A) 涂覆到卡箍 (4) 的螺纹和内径上。 将卡箍 (4) 拧紧至扭矩为
17 ± 1 N·m (150 ± 9 lb in) 。 - 将工具 (A) 涂覆到卡箍 (5) 的螺纹和内径上。 将卡箍 (5) 拧紧至扭矩为
7.5 ± 1 N·m (66 ± 9 lb in) 。Show/hide table
图 3 g06259872 - 安装护罩 (10) 和螺栓 (11)。
- 对其余涡轮增压器重复步骤 1 至步骤 9。
Show/hide table
图 4 g06259875 - 安装护罩 (13)、支架 (14) 和 11 个螺栓 (12)。
Show/hide table
图 5 g06259878 - 安装护罩 (16) 和螺栓 (15)。
Show/hide table
图 6 g06259897 - 安装支架 (18) 和螺栓 (17)。
Show/hide table
图 7 g06260182 - 安装支架 (20) 和螺栓 (19)。
Show/hide table
图 8 g06260201 - 安装支架组件 (22) 和 11 个螺栓 (21)。
Show/hide table
图 9 g06260205 - 安装空气滤清器组件 (23)，四个螺栓 (27)，然后连接软管 (26)。
- 拧紧带夹 (24)。
- 将工具 (B) 涂覆到带夹 (25) 所在软管的内径上。 拧紧带夹 (25)。
- 对其余的空气滤清器组件重复步骤 16 至 18。
Show/hide table
| |
| 图 1 | g06259613 |
Caterpillar Information System:
G3516 TA Engine Prelube Pump - Air
336 Excavator Machine Systems Refrigerant Receiver-Dryer - Remove and Install
3500E Marine Engines Sound Information
Regulatory Compliance Information General Information
New Exhaust Manifold Brackets Are Now Used on Certain G3500 Engines {0635, 1061} New Exhaust Manifold Brackets Are Now Used on Certain G3500 Engines {0635, 1061}
323F LN Excavator Machine Systems Pump Control (Negative Flow) - Test
G3516 Petroleum Engines Gear Group (Rear) - Remove
XQP1100 Generator Set Configuration Parameters
New Improved Emergency Stop Switch Contact Block is Now Used on Certain Gensets {1408, 7418} New Improved Emergency Stop Switch Contact Block is Now Used on Certain Gensets {1408, 7418}
New Harness Is Now Used on Certain G3600 Engines {1408} New Harness Is Now Used on Certain G3600 Engines {1408}
New Cage Clamp Style Terminal Block on Certain G3600 A4 ECM Terminal Blocks {4460, 4490, 7426, 7451} New Cage Clamp Style Terminal Block on Certain G3600 A4 ECM Terminal Blocks {4460, 4490, 7426, 7451}
NOx Sensor Installation and Handling Procedures for Certain G3500H Series Engines {1335, 1408, 191N} NOx Sensor Installation and Handling Procedures for Certain G3500H Series Engines {1335, 1408, 191N}
G3516 Petroleum Engines Gear Group (Rear) - Install
New Brake Software is Now Available For Certain F Series Large Off-Highway Trucks {7610, 7620} New Brake Software is Now Available For Certain F Series Large Off-Highway Trucks {7610, 7620}
G3516 Engines Camshaft Bearing Position
G3516 Engines Turbocharger
323F LN Excavator Machine Systems Gear Pump (Pilot) - Test
XQP1100 Generator Set Walk-Around Inspection
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Safety Messages
XQP1100 Generator Set Fuel System Primary Filter (Water Separator) Element - Replace - If Equipped
A New Insulation Assembly and Wing Plates Are Now Used on Certain C175-20 Locomotive Engines {1062, 1091} A New Insulation Assembly and Wing Plates Are Now Used on Certain C175-20 Locomotive Engines {1062, 1091}
XQP1100 Generator Set Belts - Inspect/Adjust/Replace
XQP1100 Generator Set Engine Oil Sample - Obtain
336 Excavator Machine Systems Refrigerant Condenser - Remove and Install