Gear Group (Rear) - Remove
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1P-0520 | Driver Group | 1 |
Start By:
- Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove".
- Remove the crankshaft rear seal and wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Rear Seal and Wear Sleeve - Remove".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Remove four bolts (1), plate, (2) and gear (3).
Show/hide table
Illustration 2 g06259459 - Use Tooling (A) and a suitable press to remove bearing (4) from gear (3).
Show/hide table
Illustration 3 g06259470 - Remove six bolts (5), camshaft idler gears (4).
Show/hide table
Illustration 4 g06259503 - Remove thrust washers (8).
Show/hide table
Illustration 5 g06259579 - Remove idler shaft (9).
- Use Tooling (A) and a suitable press to remove bearings (10).
Show/hide table
Illustration 6 g06259595 - Remove four bolts (11) and remove gear shaft (12).
Show/hide table
Illustration 7 g06259599 - Remove 12 bolts (13) and crankshaft gear (14).
Show/hide table
| |
| Illustration 1 | g06259447 |
Caterpillar Information System:
XQP1100 Generator Set Configuration Parameters
New Improved Emergency Stop Switch Contact Block is Now Used on Certain Gensets {1408, 7418} New Improved Emergency Stop Switch Contact Block is Now Used on Certain Gensets {1408, 7418}
New Harness Is Now Used on Certain G3600 Engines {1408} New Harness Is Now Used on Certain G3600 Engines {1408}
New Cage Clamp Style Terminal Block on Certain G3600 A4 ECM Terminal Blocks {4460, 4490, 7426, 7451} New Cage Clamp Style Terminal Block on Certain G3600 A4 ECM Terminal Blocks {4460, 4490, 7426, 7451}
NOx Sensor Installation and Handling Procedures for Certain G3500H Series Engines {1335, 1408, 191N} NOx Sensor Installation and Handling Procedures for Certain G3500H Series Engines {1335, 1408, 191N}
G3516 TA Engine Compression
G3516 TA Engine Exhaust Bypass Valve - Wastegate
Smart Engine Management System (Smart EMS) HMI User Guide {1900, 1901, 1920, 7490, 7606, 7610, 7620, 79D0} Smart Engine Management System (Smart EMS) HMI User Guide {1900, 1901, 1920, 7490, 7606, 7610, 7620, 79D0}
G3516 TA Engine Crankshaft
C280-08 Marine Engine General Hazard Information
Installing a New Control Assembly for the Marine Monitoring System (MMS) {1900, 1901} Installing a New Control Assembly for the Marine Monitoring System (MMS) {1900, 1901}
A New Oil Cooler Available for Certain 3512C Well Service Engines {1378} A New Oil Cooler Available for Certain 3512C Well Service Engines {1378}
323F LN Excavator Machine Systems Pump Control (Negative Flow) - Test
New Exhaust Manifold Brackets Are Now Used on Certain G3500 Engines {0635, 1061} New Exhaust Manifold Brackets Are Now Used on Certain G3500 Engines {0635, 1061}
Regulatory Compliance Information General Information
3500E Marine Engines Sound Information
336 Excavator Machine Systems Refrigerant Receiver-Dryer - Remove and Install
G3516 TA Engine Prelube Pump - Air
3512E and 3516E Marine Engines Turbocharger - Install
G3516 Petroleum Engines Gear Group (Rear) - Install
New Brake Software is Now Available For Certain F Series Large Off-Highway Trucks {7610, 7620} New Brake Software is Now Available For Certain F Series Large Off-Highway Trucks {7610, 7620}
G3516 Engines Camshaft Bearing Position
G3516 Engines Turbocharger
323F LN Excavator Machine Systems Gear Pump (Pilot) - Test