New Cage Clamp Style Terminal Block on Certain G3600 A4 ECM Terminal Blocks {4460, 4490, 7426, 7451}
- Engine
- G3606 (S/N: JFE100-286,800-866)
- G3608 (S/N: XH7100-174,701-816,818-818)
- G3612 (S/N: BB2100-122,701-743)
- G3616 (S/N: ZZY101-160,701-743)
- G3608 (S/N: XH7100-174,701-816,818-818)
Description Of Change: Replace screw type terminal block with a cage clamp style terminal block that provides better wire retention in application with vibration.
Adaptable To: The following changes are adaptable to the products within the listed affected serial numbers, and are effective with all products listed in the effective serial numbers.
Show/hide table
Qty | New Part Number | Description | Former Part Number |
---|---|---|---|
7 | Block Terminal | ||
2 | End Cover | N/A | |
1 | Bridge Bar | ||
1 | Marker As | ||
1 | Bridge Bar |
Show/hide table
Effective Serial Numbers |
---|
S/N:JFE00877-UP |
S/N:XH700817,819-UP |
S/N:ZZY00744-UP |
S/N:BB200744-UP |
Caterpillar Information System:
NOx Sensor Installation and Handling Procedures for Certain G3500H Series Engines {1335, 1408, 191N} NOx Sensor Installation and Handling Procedures for Certain G3500H Series Engines {1335, 1408, 191N}
G3516 TA Engine Compression
G3516 TA Engine Exhaust Bypass Valve - Wastegate
Smart Engine Management System (Smart EMS) HMI User Guide {1900, 1901, 1920, 7490, 7606, 7610, 7620, 79D0} Smart Engine Management System (Smart EMS) HMI User Guide {1900, 1901, 1920, 7490, 7606, 7610, 7620, 79D0}
G3516 TA Engine Crankshaft
C280-08 Marine Engine General Hazard Information
Installing a New Control Assembly for the Marine Monitoring System (MMS) {1900, 1901} Installing a New Control Assembly for the Marine Monitoring System (MMS) {1900, 1901}
A New Oil Cooler Available for Certain 3512C Well Service Engines {1378} A New Oil Cooler Available for Certain 3512C Well Service Engines {1378}
G3516 TA Engine Air/Fuel Ratio Control - Oxygen Feedback
Rework Procedure for New Support Bracket on Certain 374F and 390F Excavators Equipped with C18 Engines {1405, 1802} Rework Procedure for New Support Bracket on Certain 374F and 390F Excavators Equipped with C18 Engines {1405, 1802}
G3516 Petroleum Engines Oil Temperature Regulators - Remove and Install
793F Off-Highway Truck Engine Supplement Temperature Sensor (Exhaust Inlet) - Remove and Install
New Harness Is Now Used on Certain G3600 Engines {1408} New Harness Is Now Used on Certain G3600 Engines {1408}
New Improved Emergency Stop Switch Contact Block is Now Used on Certain Gensets {1408, 7418} New Improved Emergency Stop Switch Contact Block is Now Used on Certain Gensets {1408, 7418}
XQP1100 Generator Set Configuration Parameters
G3516 Petroleum Engines Gear Group (Rear) - Remove
323F LN Excavator Machine Systems Pump Control (Negative Flow) - Test
New Exhaust Manifold Brackets Are Now Used on Certain G3500 Engines {0635, 1061} New Exhaust Manifold Brackets Are Now Used on Certain G3500 Engines {0635, 1061}
Regulatory Compliance Information General Information
3500E Marine Engines Sound Information
336 Excavator Machine Systems Refrigerant Receiver-Dryer - Remove and Install
G3516 TA Engine Prelube Pump - Air
3512E and 3516E Marine Engines Turbocharger - Install
G3516 Petroleum Engines Gear Group (Rear) - Install