Visual Inspection
目视检查系统是故障诊断和排除的第一步。 目视检查之前,应关闭发动机,并把所有作业机具下放到地面。
- 检查液压油箱里的油位。
注: 利用以下步骤释放回油液压回路中可能存在的压力。 参考图 1 以了解加注口盖位置。
- 逆时针转动加注口盖并将箭头从位置 (A) 移至位置 (B)。
- 将箭头从位置 (B) 移至位置 (C),以便释放压力至少 45 秒。
- 释放油箱压力后,将盖从位置 (C) 转到位置 (D)。 拆卸加注口盖。
Show/hide table图 1 g06184990 加注口盖
(A) 锁定位置
(B) 压力释放 - 开始位置
(C) 压力释放 - 结束位置
(D) 打开位置Show/hide table注意 在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。
有关收集和盛接 Cat® 产品油液的合适工具和用品,请参考专门出版物, NENG2500, "代理商维修工具目录"。
按照本地法规和要求处置所有油液。
- 拆下液压滤清器滤芯。 检查液压滤清器中有无材料显示部件被损坏。
- 检查所有管路和连接是否损坏或泄露。
- 检查控制连杆机构有无部件弯曲、断裂或损坏。
Caterpillar Information System:
320 GC, 320 and 323 Excavator Machine Systems General Testing and Adjusting Information
C175 Tier 4 Final Engines for Off-Highway Trucks Aftercooler - Test
C9.3B Engines for Caterpillar Built Machines Flywheel - Install
Installation of New Cylinder Heads and Camshafts on Certain 3512E Petroleum Tier 4 Final Engines {0703, 1100, 1209, 1210} Installation of New Cylinder Heads and Camshafts on Certain 3512E Petroleum Tier 4 Final Engines {0703, 1100, 1209, 1210}
C12.9 Marine Propulsion Engine Cylinder Liner Projection - Inspect
G3516 Petroleum Engine Hoses and Clamps - Inspect/Replace
Lubrication of the Fuel Injection Pump on Certain C0.5, C0.7, C1.1, C1.5, and C2.2 Engines {1251, 1257, 1265} Lubrication of the Fuel Injection Pump on Certain C0.5, C0.7, C1.1, C1.5, and C2.2 Engines {1251, 1257, 1265}
CX38-P892 Well Servicing Transmission Transmission Hydraulic Control
320 GC, 320, 323, 330 GC and 330 Excavator Machine Systems Troubleshooting Diagnostic Trouble Codes
XQP1100 Generator Set Maintenance Interval Schedule - Prime
C12.9 Marine Propulsion Engine Rear Gear Group - Time
G3516 Petroleum Engine Coolant (NGEC) - Change
320 GC, 320 and 323 Excavator Machine Systems Main Hydraulic Pump Air - Purge
320 GC, 320 and 323 Excavator Machine Systems Overload Warning - Set - If Equipped
320 GC, 320 and 323 Excavator Machine Systems Operational Checks
320 GC, 320 and 323 Excavator Machine Systems Automatic Travel Speed Control - Test
320 GC, 320 and 323 Excavator Machine Systems Machine Drift on a Slope - Check
320 GC, 320 and 323 Excavator Machine Systems Swing Speed and Overswing on Level Ground - Check
320 GC, 320 and 323 Excavator Machine Systems Swing Speed and Swing Drift on a Slope - Check
320 GC, 320 and 323 Excavator Machine Systems Cylinder Drift - Check - Loaded Bucket
320 GC, 320 and 323 Excavator Machine Systems Cylinder Speed - Check
320 GC, 320, 323, 330 GC and 330 Excavator Machine Systems Troubleshooting Event Codes
C175 Tier 4 Final Engines for Off-Highway Trucks Finding the Top Center Position for the No. 1 Piston
Pump Electronic Monitoring System for Well Stimulation Pumps Electrical Power Supply - Test