Swing Speed and Overswing on Level Ground - Check
Show/hide table
"在平地上的回转速度和摆动过量 - 检查" | |||
---|---|---|---|
摆动过量 mm(in) | |||
项目 | 新 | 维修极限 | 来自压力表的 |
向右回转 | |
|
|
向左回转 | |||
回转时间(1) (秒) | |||
项目 | 新 | 维修极限 | 来自压力表的 |
向右回转 | 4.5 或以下 | 5.5 或以下 | |
向左回转 |
Show/hide table
(1) | 完成 180 度回转操作所需的时间 |
测量机器的回转速度和回转过量可以确定是否需要检查回转马达或反作用阀。 精细回转控制开关(如有配备)必须处在断开位置。
注: 发动机转速和 / 或测试期间所用的机器配置可能对测试结果产生影响。 有关此项测试所用的发动机转速,请参阅测试和调整, "发动机性能 - 测试(发动机转速)"。 有关此项测试所用的机器配置,请参阅测试和调整, "操作检查"。
注: 执行操作检查之前,必须根据卸压阀压力技术规范设定卸压阀压力。 请参阅测试和调整, "技术规范"。
Show/hide table
所需工具 | |
---|---|
说明 | 数量 |
卷尺 | 1 |
秒表 | 1 |
Show/hide table
图 1 | g06191977 |
- 将机器停放在水平地面上。 参考图 1。
注: 铲斗应空载。
- 停止发动机。
Show/hide table
图 2 g06194809 (A) 上部机架
(B) 底盘机架
(C) 标记 - 为了指示这两个位置之间的关系,在回转轴承的内座圈和外座圈上作一个标记 (C)。 标记用于使回转操作停止的目标。 参考图 2。
- 起动发动机。
- 向任一方向移动回转操纵手柄,直到机器完成一次远离目标的 180 度回转操作。
- 向任一方向移动回转操纵手柄,直到机器完成一次朝向目标的 180 度回转操作。 将回转操纵手柄移回目标处的空档位置。
- 测量回转轴承上标记之间的距离,获得回转过量的量。 参考图 2。
注: 使用从操作员座椅处可以看见的一点作为目标参考点。
Caterpillar Information System:
320 GC, 320 and 323 Excavator Machine Systems Machine Drift on a Slope - Check
320 GC, 320 and 323 Excavator Machine Systems Automatic Travel Speed Control - Test
320 GC, 320 and 323 Excavator Machine Systems Operational Checks
320 GC, 320 and 323 Excavator Machine Systems Overload Warning - Set - If Equipped
320 GC, 320 and 323 Excavator Machine Systems Main Hydraulic Pump Air - Purge
320 GC, 320 and 323 Excavator Machine Systems Visual Inspection
320 GC, 320 and 323 Excavator Machine Systems General Testing and Adjusting Information
C175 Tier 4 Final Engines for Off-Highway Trucks Aftercooler - Test
C9.3B Engines for Caterpillar Built Machines Flywheel - Install
Installation of New Cylinder Heads and Camshafts on Certain 3512E Petroleum Tier 4 Final Engines {0703, 1100, 1209, 1210} Installation of New Cylinder Heads and Camshafts on Certain 3512E Petroleum Tier 4 Final Engines {0703, 1100, 1209, 1210}
C12.9 Marine Propulsion Engine Cylinder Liner Projection - Inspect
G3516 Petroleum Engine Hoses and Clamps - Inspect/Replace
320 GC, 320 and 323 Excavator Machine Systems Swing Speed and Swing Drift on a Slope - Check
320 GC, 320 and 323 Excavator Machine Systems Cylinder Drift - Check - Loaded Bucket
320 GC, 320 and 323 Excavator Machine Systems Cylinder Speed - Check
320 GC, 320, 323, 330 GC and 330 Excavator Machine Systems Troubleshooting Event Codes
C175 Tier 4 Final Engines for Off-Highway Trucks Finding the Top Center Position for the No. 1 Piston
Pump Electronic Monitoring System for Well Stimulation Pumps Electrical Power Supply - Test
Pump Electronic Monitoring System for Well Stimulation Pumps Sensor Supply - Test
320 GC, 320 and 323 Excavator Machine Systems Cylinder Drift - Check - Empty Bucket
320 GC, 320, 323, 330 GC and 330 Excavator Machine Systems Troubleshooting System Schematic
Ring Groove Gauges for 3500 Engines with Square Ring Groove Pistons {0701, 1214, 1215, 1216} Ring Groove Gauges for 3500 Engines with Square Ring Groove Pistons {0701, 1214, 1215, 1216}
CX38-P892 Well Servicing Transmission Transmission Warm-up
CX38-P892 Well Servicing Transmission Speed Sensor (Transmission)