Main Hydraulic Pump Air - Purge
完成主泵维修或液压油更换后,请排除液压系统中的空气。 用下述方式排除液压系统中的空气:
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 有关收集和盛接 Cat® 产品油液的合适工具和用品,请参考专门出版物, NENG2500, "代理商维修工具目录"。 按照本地法规和要求处置所有油液。 |
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下液压系统的部件或管路时,确保所有的作业机具都已降到地面上,而且液压油温度已冷。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
- 发动机停止时,将软管 (1) 从弯头 (2) 上断开。
- 从泵壳体上拆下弯头 (2) 和 O 形密封圈 (3)。
- 向主泵注油。
- 在泵壳体处安装新 O 形密封圈 (3) 和弯头 (2)。
- 将软管 (1) 连接到弯头 (2) 上。 将软管 (1) 紧固至规定的扭矩。
Show/hide table
注意 为避免损坏系统,请确保在起动前适当地给液压泵加注液压油。
- 起动发动机。
- 将发动机置于低怠速位置。 提升动臂并将动臂保持在此位置。
- 停止发动机并慢慢地降下动臂,直到作业机具降到地面上。 此步骤对液压油箱进行加压。
- 慢慢地松开软管 (1),直到油开始在软管接头周围流动。
- 将软管 (1) 紧固至规定的扭矩。
Show/hide table
图 1 | g06193584 |
泵室 (1) 箱体排油软管 (2) 弯头 (3) O 形密封圈 |
Caterpillar Information System:
320 GC, 320 and 323 Excavator Machine Systems Visual Inspection
320 GC, 320 and 323 Excavator Machine Systems General Testing and Adjusting Information
C175 Tier 4 Final Engines for Off-Highway Trucks Aftercooler - Test
C9.3B Engines for Caterpillar Built Machines Flywheel - Install
Installation of New Cylinder Heads and Camshafts on Certain 3512E Petroleum Tier 4 Final Engines {0703, 1100, 1209, 1210} Installation of New Cylinder Heads and Camshafts on Certain 3512E Petroleum Tier 4 Final Engines {0703, 1100, 1209, 1210}
C12.9 Marine Propulsion Engine Cylinder Liner Projection - Inspect
G3516 Petroleum Engine Hoses and Clamps - Inspect/Replace
Lubrication of the Fuel Injection Pump on Certain C0.5, C0.7, C1.1, C1.5, and C2.2 Engines {1251, 1257, 1265} Lubrication of the Fuel Injection Pump on Certain C0.5, C0.7, C1.1, C1.5, and C2.2 Engines {1251, 1257, 1265}
CX38-P892 Well Servicing Transmission Transmission Hydraulic Control
320 GC, 320, 323, 330 GC and 330 Excavator Machine Systems Troubleshooting Diagnostic Trouble Codes
XQP1100 Generator Set Maintenance Interval Schedule - Prime
C12.9 Marine Propulsion Engine Rear Gear Group - Time
320 GC, 320 and 323 Excavator Machine Systems Overload Warning - Set - If Equipped
320 GC, 320 and 323 Excavator Machine Systems Operational Checks
320 GC, 320 and 323 Excavator Machine Systems Automatic Travel Speed Control - Test
320 GC, 320 and 323 Excavator Machine Systems Machine Drift on a Slope - Check
320 GC, 320 and 323 Excavator Machine Systems Swing Speed and Overswing on Level Ground - Check
320 GC, 320 and 323 Excavator Machine Systems Swing Speed and Swing Drift on a Slope - Check
320 GC, 320 and 323 Excavator Machine Systems Cylinder Drift - Check - Loaded Bucket
320 GC, 320 and 323 Excavator Machine Systems Cylinder Speed - Check
320 GC, 320, 323, 330 GC and 330 Excavator Machine Systems Troubleshooting Event Codes
C175 Tier 4 Final Engines for Off-Highway Trucks Finding the Top Center Position for the No. 1 Piston
Pump Electronic Monitoring System for Well Stimulation Pumps Electrical Power Supply - Test
Pump Electronic Monitoring System for Well Stimulation Pumps Sensor Supply - Test