Swing Speed and Swing Drift on a Slope - Check
Show/hide table
"在斜坡上的回转速度和摆动过量" | |||
---|---|---|---|
回转时间(秒) | |||
项目 | 新 | 维修极限 | 来自压力表的 |
向右回转 | 3.5 或以下 | 4.6 或以下 | |
向左回转 | |||
回转漂移 mm(in) | |||
项目 | 新 | 维修极限 | 来自压力表的 |
向右回转 | 0 | 0 | |
向左回转 |
在斜坡上测量回转速度可以确定是否需要检查回转马达和反作用阀。 在斜坡上测量回转漂移可以确定是否需要检查回转停车制动器。
注: 发动机转速和 / 或测试期间所用的机器配置可能对测试结果产生影响。 有关此项测试所用的发动机转速,请参阅测试和调整, "发动机性能 - 测试(发动机转速)"。 有关此项测试所用的机器配置,请参阅测试和调整, "操作检查"。
注: 执行操作检查之前,必须根据卸压阀压力技术规范设定卸压阀压力。 请参阅测试和调整, "技术规范"。
Show/hide table
所需工具 | |
---|---|
说明 | 数量 |
卷尺 | 1 |
秒表 | 1 |
Show/hide table
图 1 | g06192050 |
为在斜坡上测量回转速度,请完成下列步骤。
- 作业工具应空载。
- 将机器安置在 12 度斜坡上。 参考图 1。
- 使作业机具处于最大工作范围,并关闭作业工具。 将作业工具离地放置,使其不会碰到任何障碍物。
Show/hide table
图 2 g06192085 - 将上部结构安置在位置 (A)。 上部结构应与下部结构成 90 度角。 参考图 2。
- 测量上部结构从位置 (A) 回转到位置 (B) 所需的时间。
- 将上部结构安置在位置 (C)。 上部结构应与下部结构成 90 度角。
- 测量上部结构从位置 (C) 回转到位置 (B) 所需的时间。
为在斜坡上测量回转沉降,请完成下列步骤。
- 将上部结构安置在位置 (A)。 上部结构应与下部结构成 90 度角。 参考图 2。
Show/hide table
图 3 g06236078 (D) 上部机架
(E) 底盘机架
(F) 标记 - 为了指示这两个位置之间的关系,在回转轴承的内座圈和外座圈上作一个标记 (F)。 参考图 3。
- 停止发动机。
- 将机器停放在此位置 3 分钟。 测量回转轴承圆周上的回转漂移。
- 起动发动机。
- 将上部结构安置在位置 (C)。 上部结构应与下部结构成 90 度角。 参考图 2。
- 重复步骤 2 至 4。
Caterpillar Information System:
320 GC, 320 and 323 Excavator Machine Systems Swing Speed and Overswing on Level Ground - Check
320 GC, 320 and 323 Excavator Machine Systems Machine Drift on a Slope - Check
320 GC, 320 and 323 Excavator Machine Systems Automatic Travel Speed Control - Test
320 GC, 320 and 323 Excavator Machine Systems Operational Checks
320 GC, 320 and 323 Excavator Machine Systems Overload Warning - Set - If Equipped
320 GC, 320 and 323 Excavator Machine Systems Main Hydraulic Pump Air - Purge
320 GC, 320 and 323 Excavator Machine Systems Visual Inspection
320 GC, 320 and 323 Excavator Machine Systems General Testing and Adjusting Information
C175 Tier 4 Final Engines for Off-Highway Trucks Aftercooler - Test
C9.3B Engines for Caterpillar Built Machines Flywheel - Install
Installation of New Cylinder Heads and Camshafts on Certain 3512E Petroleum Tier 4 Final Engines {0703, 1100, 1209, 1210} Installation of New Cylinder Heads and Camshafts on Certain 3512E Petroleum Tier 4 Final Engines {0703, 1100, 1209, 1210}
C12.9 Marine Propulsion Engine Cylinder Liner Projection - Inspect
320 GC, 320 and 323 Excavator Machine Systems Cylinder Drift - Check - Loaded Bucket
320 GC, 320 and 323 Excavator Machine Systems Cylinder Speed - Check
320 GC, 320, 323, 330 GC and 330 Excavator Machine Systems Troubleshooting Event Codes
C175 Tier 4 Final Engines for Off-Highway Trucks Finding the Top Center Position for the No. 1 Piston
Pump Electronic Monitoring System for Well Stimulation Pumps Electrical Power Supply - Test
Pump Electronic Monitoring System for Well Stimulation Pumps Sensor Supply - Test
320 GC, 320 and 323 Excavator Machine Systems Cylinder Drift - Check - Empty Bucket
320 GC, 320, 323, 330 GC and 330 Excavator Machine Systems Troubleshooting System Schematic
Ring Groove Gauges for 3500 Engines with Square Ring Groove Pistons {0701, 1214, 1215, 1216} Ring Groove Gauges for 3500 Engines with Square Ring Groove Pistons {0701, 1214, 1215, 1216}
CX38-P892 Well Servicing Transmission Transmission Warm-up
CX38-P892 Well Servicing Transmission Speed Sensor (Transmission)
CX38-P892 Well Servicing Transmission Transmission Control