Water Pump Seal - Remove
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 9S-1366 | 螺栓 | 2 |
注: 当将水泵安装到发动机上时,可以更换水泵密封件。 使用下列步骤来更换水泵密封件。
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 从冷却系统将冷却液排入合适的容器以便保存或废弃这些冷却液。 请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
Show/hide table
图 1 g03891807 - 将适配器 (1) 从管和水泵 (2) 上断开。 拆下适配器 (1)。
- 拆下弯头 (3)。
Show/hide table
图 2 g01206688 - 拆下螺栓 (9) 和壳体 (4)。
- 从壳体上拆下 O 形密封圈 (8)。
- 松开将叶轮 (7)固定入位的螺栓 (5)。 不要将螺栓拆下来。
- 使用一个挡块和工具 (A)使叶轮 (7)张紧。 轻敲挡块中间,使叶轮 (7)在轴上松动。
- 从轴上拆下以下部件:螺栓 (5)、垫圈 (6) 和叶轮 (7)。
- 拆下密封件总成 (10)。
Caterpillar Information System:
A New Snubber Is Now Used on Certain C18 Marine Engines {1274} A New Snubber Is Now Used on Certain C18 Marine Engines {1274}
C13 and C15 Engines for Combat and Tactical Vehicles Engine Temperature Sensor Open or Short Circuit - Test
C3.3B and C3.8 Engines for Caterpillar Built Machines DEF Line Heater - Test
No Fault Found for 379-0150 Fuel Injection Pump Gp for C9.3 Engines {1251} No Fault Found for 379-0150 Fuel Injection Pump Gp for C9.3 Engines {1251}
G3508J, G3516J, and G3520J Engines Engine Oil Filter Housing - Assemble
C3.3B and C3.8 Engines for Caterpillar Built Machines SCR Catalyst Has Incorrect Inlet Temperature
G3508J, G3516J, and G3520J Engines Engine Oil Filter Housing - Disassemble
C3.3B and C3.8 Engines for Caterpillar Built Machines DEF Tank Temperature Is Low
G3508J, G3516J, and G3520J Engines Engine Oil Cooler - Assemble
G3508J, G3516J, and G3520J Engines Engine Oil Cooler - Disassemble
G3508J, G3516J, and G3520J Engines Engine Oil Pump - Assemble
G3508J, G3516J, and G3520J Engines Engine Oil Pump - Disassemble
C1.7 and C2.2 Industrial Engines Fuel System Secondary Filter - Replace
G3612 and G3616 Engines Water Pump Seal - Install
Overspeed Guidance for 3500 and C175 Machine Engines{1000, 1915, 7410, 7427, 7490} Overspeed Guidance for 3500 and C175 Machine Engines{1000, 1915, 7410, 7427, 7490}
725C2 Articulated Truck Product Identification Number
A New Exhaust Manifold Band Clamp Is Used on Certain 3500 Locomotive and Marine Engines {1059} A New Exhaust Manifold Band Clamp Is Used on Certain 3500 Locomotive and Marine Engines {1059}
2015/09/23 A Procedure for Piston and Piston Pin Break-In for Certain C18 Engines is Now Available {1225}
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System General Information
G3508J, G3516J, and G3520J Engines Engine Oil and Water Pump Drive - Remove
G3508J, G3516J, and G3520J Engines Engine Oil and Water Pump Drive - Disassemble
G3508J, G3516J, and G3520J Engines Engine Oil and Water Pump Drive - Assemble
G3508J, G3516J, and G3520J Engines Engine Oil and Water Pump Drive - Install
G3508J, G3516J, and G3520J Engines Engine Oil Pan - Disassemble