Engine Oil and Water Pump Drive - Disassemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-0520 | Driver Group | 1 |
Start By:
- Remove the engine oil and water pump drive.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove O-ring seal (3).
- Remove the bolts and washers (2). Remove rear adapter assembly (4) from shaft assembly (1).
Show/hide table
Illustration 2 g01254536 - Remove O-ring seals (6) and (7) from rear adapter assembly (4).
- Use Tooling (A) and a suitable press to remove bearing (5).
Show/hide table
Illustration 3 g00590612 - Remove bolts (9) from shaft assembly (1). Remove gears (8) and (10) from shaft assembly (1).
Show/hide table
Illustration 4 g00590613 - Remove O-ring seal (13) from front adapter assembly (12).
- Use Tooling (A) and a suitable press to remove bearing (11) from front adapter assembly (12).
Show/hide table
Illustration 1 | g01254535 |
Caterpillar Information System:
G3508J, G3516J, and G3520J Engines Engine Oil and Water Pump Drive - Remove
PM620, PM622, PM820, PM822 and PM825 Cold Planers Electronic System General Information
2015/09/23 A Procedure for Piston and Piston Pin Break-In for Certain C18 Engines is Now Available {1225}
A New Exhaust Manifold Band Clamp Is Used on Certain 3500 Locomotive and Marine Engines {1059} A New Exhaust Manifold Band Clamp Is Used on Certain 3500 Locomotive and Marine Engines {1059}
725C2 Articulated Truck Product Identification Number
Overspeed Guidance for 3500 and C175 Machine Engines{1000, 1915, 7410, 7427, 7490} Overspeed Guidance for 3500 and C175 Machine Engines{1000, 1915, 7410, 7427, 7490}
G3612 and G3616 Engines Water Pump Seal - Install
C1.7 and C2.2 Industrial Engines Fuel System Secondary Filter - Replace
G3612 and G3616 Engines Water Pump Seal - Remove
A New Snubber Is Now Used on Certain C18 Marine Engines {1274} A New Snubber Is Now Used on Certain C18 Marine Engines {1274}
C13 and C15 Engines for Combat and Tactical Vehicles Engine Temperature Sensor Open or Short Circuit - Test
C3.3B and C3.8 Engines for Caterpillar Built Machines DEF Line Heater - Test
G3508J, G3516J, and G3520J Engines Engine Oil and Water Pump Drive - Assemble
G3508J, G3516J, and G3520J Engines Engine Oil and Water Pump Drive - Install
G3508J, G3516J, and G3520J Engines Engine Oil Pan - Disassemble
G3508J, G3516J, and G3520J Engines Engine Oil Pan - Assemble
G3508J, G3516J, and G3520J Engines Engine Oil Sequence Valves - Remove and Install
G3508J, G3516J, and G3520J Engines Drive Housing (Front) - Remove and Install
G3508J, G3516J, and G3520J Engines Flywheel Housing - Remove
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Diagnostic Trouble Codes
794 AC Off-Highway Truck Machine Systems Hydraulic Tank (Brake, Hoist, Steering) - Remove and Install
G3508J, G3516J, and G3520J Engines Flywheel Housing - Install
G3508J, G3516J, and G3520J Engines Crankshaft Front Seal and Wear Sleeve - Remove
G3508J, G3516J, and G3520J Engines Crankshaft Front Seal and Wear Sleeve - Install