DEF Tank Temperature Is Low
Show/hide table
DEF 罐温度低故障诊断代码 | ||
---|---|---|
J1939 代码和描述 | 代码的前提条件 | 意见 |
3031-2
后处理 #1 DEF 罐温度:不稳定、间歇或不正确 |
- 蓄电池电压正常
- 钥匙开关信号(ECM:V13 和 V33,DCU:18 端子)持续激活超过 2 秒 - 除起动马达停止后 2 秒外,起动马达开关信号(ECM:V12 端子)未处于激活状态 - DCU 和发动机 ECM 之间的 CAN 通信正常 - DCU 和罐传感器之间的 CAN 通信正常 - DTC:DEF 罐温度传感器错误:未检测到超出范围低 (SPN 3031, FMI 4) - DTC:DEF 罐温度传感器错误:未检测到超出范围高 (SPN 3031, FMI 3) |
DEF 罐温度传感器数据超出范围,或者数据消息超时持续 12 秒或更长时间 |
3031-3
后处理 #1 DEF 罐温度:电压高于正常值 |
- 蓄电池电压正常
- 钥匙开关信号(ECM:V13 和 V33,DCU:18 端子)持续激活超过 2 秒 - 除起动马达停止后 2 秒外,起动马达开关信号(ECM:V12 端子)未处于激活状态 - DCU 和发动机 ECM 之间的 CAN 通信正常 - DCU 和罐传感器之间的 CAN 通信正常 |
通过 CAN 接收自 DEF 罐的温度传感器 FMI 指示 FMI 4(传感器元件开路)持续 2 秒或更长时间 |
3031-4
后处理 #1 DEF 罐温度:电压低于正常值 |
通过 CAN 接收自 DEF 罐的温度传感器 FMI 指示 FMI 4(传感器元件短路)持续 2 秒或更长时间 | |
遵循故障诊断与排除步骤来确定故障根源。 |
DEF 罐传感器组件在组件内具有温度传感器。 DEF 温度通过 CAN 通信传送到 DCU。
Show/hide table
故障诊断与排除测试步骤 | 数值 | 结果 |
---|---|---|
1. 检查代码 A. 连接 Caterpillar 电子技师 (ET) 和 DCU。 如有必要,请参阅故障诊断与排除, "电子维修工具"。 B. 523616-2 与罐传感器无 CAN 通信是否处于激活或记录状态。 |
523616-2 |
结果:如果 523616-2 代码为激活或记录状态,首先对该代码进行故障诊断与排除。 结果:如果 523616-2 代码不是激活或记录状态。 转至测试步骤 2。 |
2. 检查 DEF 质量 A. 检查 DEF 质量。 请参阅测试和调整, "柴油机排气处理液质量 – 测试"。 |
DEF 质量符合标准 |
结果:如果 DEF 受到污染。 修理:更换 DEF 罐传感器组件,并冲洗 DEF 罐。 请参阅测试和调整, "柴油机排气处理液罐 – 冲洗"。 结果:DEF 符合技术规格 转至测试步骤 3。 |
3. 检查代码 A. 将钥匙开关转到断开位置,然后再转到接通位置。 B. 等待至少 47 秒,以确认代码是否重现。 |
代码激活 |
结果:代码仍处于激活状态。 修理:然后更换 DEF 罐传感器组件 结果:代码没有重现。 返回工作。 |
Caterpillar Information System:
G3508J, G3516J, and G3520J Engines Engine Oil Cooler - Assemble
G3508J, G3516J, and G3520J Engines Engine Oil Cooler - Disassemble
G3508J, G3516J, and G3520J Engines Engine Oil Pump - Assemble
G3508J, G3516J, and G3520J Engines Engine Oil Pump - Disassemble
G3508J, G3516J, and G3520J Engines Auxiliary Water Pump - Assemble
G3508J, G3516J, and G3520J Engines Water Pump - Disassemble
C13 Engine for Combat and Tactical Vehicles Finding Top Center Position for No. 1 Piston
G3508J, G3516J, and G3520J Engines Thermostatic Valve - Assemble
G3508J, G3516J, and G3520J Engines Thermostatic Valve - Disassemble
G3508J, G3516J, and G3520J Engines Throttle Control Valve - Install
G3508J, G3516J, and G3520J Engines Throttle Control Valve - Remove
C3.3B and C3.8 Engines for Caterpillar Built Machines DEF Tank Temperature Is High
G3508J, G3516J, and G3520J Engines Engine Oil Filter Housing - Disassemble
C3.3B and C3.8 Engines for Caterpillar Built Machines SCR Catalyst Has Incorrect Inlet Temperature
G3508J, G3516J, and G3520J Engines Engine Oil Filter Housing - Assemble
No Fault Found for 379-0150 Fuel Injection Pump Gp for C9.3 Engines {1251} No Fault Found for 379-0150 Fuel Injection Pump Gp for C9.3 Engines {1251}
C3.3B and C3.8 Engines for Caterpillar Built Machines DEF Line Heater - Test
C13 and C15 Engines for Combat and Tactical Vehicles Engine Temperature Sensor Open or Short Circuit - Test
A New Snubber Is Now Used on Certain C18 Marine Engines {1274} A New Snubber Is Now Used on Certain C18 Marine Engines {1274}
G3612 and G3616 Engines Water Pump Seal - Remove
C1.7 and C2.2 Industrial Engines Fuel System Secondary Filter - Replace
G3612 and G3616 Engines Water Pump Seal - Install
Overspeed Guidance for 3500 and C175 Machine Engines{1000, 1915, 7410, 7427, 7490} Overspeed Guidance for 3500 and C175 Machine Engines{1000, 1915, 7410, 7427, 7490}
725C2 Articulated Truck Product Identification Number