Crankshaft Gear - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-2326     | Forcing Screw     | 1     |
1P-2325 | Head     | 1     | |
3H-0462 | Bolt     | 6     | |
8H-0709 | Strap     | 6     | |
5F-7373 | Jaw     | 3     |
- Use Tooling (A) to remove crankshaft gear (1) from crankshaft (2) .
Show/hide table
Illustration 1 | g03859477 |
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
B     | -     | Hot Plate     | 1     |
C     | -     | Loctite 603     | -     |
- Ensure that all components are clean and free form damage. If necessary, replace any components that are worn or damaged.
Show/hide table
Illustration 2 | g03859477 |
- Use Tooling (B) to raise the temperature of crankshaft gear (1) to 170° ± 10°C (338° ± 18°F)
Note: Do not use a torch to raise temperature of crankshaft gear (1) .
Note: Do not heat crankshaft gear (1) for more than 2 hours.
Note: Before installing crankshaft gear (1), apply tooling (C) in a 5 mm (0.2 inch) wide band approximately 30 mm (1.2 inch) away from end of crankshaft (2) where crankshaft gear (1) is to be installed.
Show/hide table
Always wear protective gloves when handling parts that have been heated. |
- Install crankshaft gear (1) onto crankshaft (2) .
Caterpillar Information System:
3512C Generator Set Engine Atmospheric Pressure Sensor - Remove and Install
3512C Generator Set Engine Crankcase Pressure Sensor - Remove and Install
XQ400 Power Module Safety Messages
2015/09/04 A New Breather Hose Is Now Used on Certain 3512 Engines {1317}
C8.7 Marine Engine Crankshaft Pulley - Remove and Install
Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000} Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}
3512C Generator Set Engine Engine Speed/Timing Sensor - Remove and Install
C280-08 Tier 4 Engine Turbocharger - Disassemble
794 AC Off-Highway Truck Field Assembly Mirror - Install
3512C Generator Set Engine Aftercooler Coolant Temperature Sensor - Remove and Install
CG137-08 and CG137-12 Engines Engine Air Cleaner Service Indicator - Inspect - If Equipped
3512C Generator Set Engine Coolant Temperature Sensor - Remove and Install
XQ400 Power Module Model View Illustrations
3512C Generator Set Engine Engine Speed Sensor - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Fuel Priming Pump and Primary Fuel Filter
349F and 352F Excavators Machine System Specifications Front Lines
C3.4B Engines General Information
C3.4B Engines Component Location
3512C Generator Set Engine Fuel Pressure Sensor - Remove and Install
C280-08 Tier 4 Engine Turbocharger - Assemble
Software Updates for Certain Tier 4 Final Industrial Engines{1000, 1920} Software Updates for Certain Tier 4 Final Industrial Engines{1000, 1920}
Installation Procedure for the 467-8080 TLV2 Seat Suspension Harness Kit{1408, 7312, 7324} Installation Procedure for the 467-8080 TLV2 Seat Suspension Harness Kit{1408, 7312, 7324}
2015/07/23 Improved Lines Group for the Seat Suspension Is Now Available for Certain Machines {7312, 7324}
3512C Generator Set Engine Air Inlet Manifold - Remove and Install