Parts and Specification Information
| |
| Illustration 1 | g03859407 |
Note: Verify that all parts are shipped and undamaged for preparation of assembly. Missing or damaged parts can be ordered prior to assembly to avoid delays during assembly.
 |
|
Personal injury or death can occur from heavy components falling during removal or installation. Properly support the component with a suitable lifting device during removal or installation. |
|
|
Climbing equipment may be required to access this service point. Refer to the Operation and Maintenance Manual, "Mounting and Dismounting" topic for safety information. |
| Item | Part Number | Description | Qty | Specification | Approximate Weight |
| 1 | 431-5921 | Support As | 1 | ||
| 2 | 7X-0346 | Bolt | 2 | ||
| 3 | 8T-4122 | Hard Washer | 7 | ||
| 4 | 434-5543 | Stud | 2 | ||
| 5 | 3K-2889 | Locknut | 2 | ||
| 6 | 431-5929 | Mirror Bracket | 1 | ||
| 7 | 431-5930 | Exhaust Clamp | 2 | ||
| 8 | 4L-6454 | Bolt | 2 | ||
| 9 | 8T-4896 | Hard Washer | 6 | ||
| 10 | 2K-4973 | Locknut | 8 | ||
| 11 | 153-4010 | Mirror As | 1 | ||
| 12 | 431-5981 | Bracket As | 1 | |
|
| 13 | 7X-0343 | Bolt | 5 | ||
| 14 | 431-5991 | Adapter As | 1 | ||
| 15 | 431-5995 | Mirror Bracket | 1 | ||
| 16 | 9B-7237 | Bolt | 4 | ||
| 17 | 431-5996 | Knob | 1 | ||
| 18 | 5P-1075 | Hard Washer | 1 | ||
| 19 | 8T-2501 | Bolt | 2 | ||
| 20 | 431-5997 | Washer | 2 | ||
| 21 | 311-7058 | Mirror Gp | 1 |
- Install support assembly (1) to the platform using two bolts (2), two hard washers (3), two studs (4), and two locknuts (5).
Note: If not already removed, remove the lifting brackets used to lift the platform assembly. Remove and replace the bolts one at a time as these bolts support the air cleaner assemblies.
- Install mirror bracket (6) to support assembly (1) using two exhaust clamps (7).
- Use two bolts (8), two hard washers (9), and two locknuts (10) to secure mirror assembly (11) to mirror bracket (6).
Show/hide table
Illustration 3 g03859504 View of the left front area of the platform - Install bracket assembly (12) to the platform using five bolts (13) and five hard washers (3).
Note: If not already removed, remove the lifting brackets used to lift the platform assembly. Remove and replace the bolts one at a time as these bolts support the air cleaner assemblies.
- Position adapter assembly (14), and mirror bracket (15) on bracket assembly (12).
- Install mirror bracket (15) to bracket assembly (12) using one bolt (16), one hard washer (9), and one locknut (10). Install knob (17) and hard washer (18) in adapter assembly (14).
- Secure adapter assembly (14) to bracket assembly (12) and adapter assembly (14) using two bolts (19), six washers (20), and two locknuts (10).
- Install mirror group (21) to adapter assembly (14) using three bolts (16), six hard washers (9), and three locknuts (10).
| |
| Illustration 2 | g03859413 |
|
View of the right front area of the platform | |
