Aftercooler - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | Krytox GPL 205 | 1 |
开始:
- 拆下执行器 (hydrax)。
- 拆下排气旁通。
- 排空冷却液。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"以了解正确的排放和加注步骤。
Show/hide table
图 1 g03833983 - 拆下螺栓 (1)、螺栓 (2)、支架 (3)、螺栓 (4)、管组件 (5) 和管组件 (6)。
Show/hide table
图 2 g03834052 - 拆下螺栓 (9)、螺栓 (10)、支架 (11)、管组件 (7)、管组件 (8) 和 O 形密封圈。
Show/hide table
图 3 g03834397 - 断开管组件 (12)。
- 拆下螺栓 (13)、螺栓 (15) 并滑回法兰 (14)。
Show/hide table
图 4 g03835129 - 拆下螺栓 (17)、支架 (16)、螺栓 (19)、支架组件 (18)、螺栓 (21)、支架 (20)、螺栓 (23) 和支架 (22)。
Show/hide table
图 5 g03835725 - 拆下螺栓 (27)。
- 将适当的起吊设备连接在盖 (25) 上。 盖 (25) 的重量约为
133 kg (293 lb) 。 - 拆下螺栓 (24)、螺栓 (26)、盖 (25) 和密封垫。
Show/hide table
图 6 g03835783 - 拆下螺栓 (28) 和板 (29)。
Show/hide table
图 7 g03836165 - 将适当的起吊设备连接到后冷器组件 (33) 上。 后冷器组件 (33) 的重量约为
370 kg (816 lb) 。 - 拆下螺栓 (30)、螺栓 (31) 和螺栓 (32)。
Show/hide table
图 8 g03836437 - 拆下螺栓 (34) 和后冷器组件 (33)。
- 按与拆卸相反的顺序安装后冷器组件 (33)。
- 将工具 (A) 涂抹到螺栓 (32) 上。
Caterpillar Information System:
C8.7 Marine Engines Expansion Tank
C9.3 Marine Engine Water Temperature Regulator - Remove and Install
C9.3 Marine Engine Water Pump - Assemble
C9.3 Marine Engine Water Pump - Disassemble
C2.2 Engines For Caterpillar Built Machines Sensor Signal (Analog, Active) - Test
Installation Procedure for Excitation Modules 10 and 15{4467} Installation Procedure for Excitation Modules 10 and 15{4467}
C9.3 Marine Engine Water Pump - Remove and Install
3516C Industrial Engine Maintenance Interval Schedule
C9.3 Marine Engine Engine Oil Pump - Remove and Install
3516C Marine Engines Diesel Exhaust Fluid Pump - Remove and Install
3516C Marine Engines Electronic Control (Diesel Exhaust Fluid) - Remove and Install
C9.3 Marine Engine Engine Oil Cooler - Remove and Install - Combined Circuit Keel Cooling
XQ400 Power Module Maintenance Interval Schedule
C9.3 Marine Engine Flywheel - Remove and Install
PM820, PM822, and PM825 Cold Planer Shipping the Machine
797F Off-Highway Truck Field Assembly Walkway (Left Hand) - Install
C9.3 Marine Engine Flywheel Housing - Remove and Install
C9.3 Marine Engine Vibration Damper and Pulley - Remove and Install
2015/05/15 A New Gas Tube Assembly Is Used on Certain 3512C Dynamic Gas Blending Oil Well Service Engines {1250}
Thinner Spacer Plates Not Recommended On Certain 3406E Through C18 On-Highway Truck Engines To Resolve Cylinder Liner Projection{1239} Thinner Spacer Plates Not Recommended On Certain 3406E Through C18 On-Highway Truck Engines To Resolve Cylinder Liner Projection{1239}
3512C and 3516C Industrial Engines Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
Procedure to Adjust Track Tension on Variable Gauge Undercarriages {4157, 4158} Procedure to Adjust Track Tension on Variable Gauge Undercarriages {4157, 4158}
C9.3 Marine Engine Front Cover - Remove and Install
C11, C13, C15, and C18 Industrial Engines NRS Exhaust Gas Temperature Is High