Electric Starting System
如果怀疑起动系统存在故障,则请使用本步骤对电气系统进行故障诊断与排除。
在 ECM 接收到钥匙开关电源后,ECM 就具备在任何时间开始发动机拖动的能力。 ECM 通过全局 CAN 数据链路收到起动指令。 如果发动机配备预润滑系统,在开始发动机拖动之前,发动机将会等待,直至完成预润滑循环为止。
配置参数
以下配置参数的设置用于控制发动机盘车:
- 起动系统 #1 曲轴循环的最大数
- 起动系统 #1 曲轴循环剩余间隔
- 起动系统 #1 曲轴持续时间
- 起动盘车终止转速
ECM 可控制安装在发动机上主起动系统对面的辅助起动系统。 请参考故障诊断与排除, "配置参数"以了解与辅助起动系统的配置参数相关的信息。
起动马达的 ECM 启动
ECM 通电电磁阀,以控制至空气起动马达的供气。
ECM 通过手动盘车继电器 #1 的常闭触点向电磁阀提供电流。
电流通过手动盘车继电器 #2 的常闭触点从电磁阀回到 ECM。
手动激活起动马达(超越控制)
使用连接到发动机接口接头中的手动拖动开关可以手动拖动发动机。 将此输入切换至蓄电池正极将通电手动盘车继电器 #1 和手动盘车继电器 #2。
此动作导致电磁阀直接连接到蓄电池正极和蓄电池负极。
蓄电池正极通过手动盘车继电器 #1 的常开触点向电磁阀提供电流。
电流通过手动盘车继电器 #2 的常开触点从电磁阀回到蓄电池负极。
Caterpillar 电子技师 (ET) 可用于超越至起动电磁阀的 ECM 输出。 超越通电电磁阀。 请查看 Cat ET 上提供的 "Starting System Relay Status(起动系统继电器状态)"来确定 ECM 输出的状态。
Caterpillar Information System:
G3500H Generator Set Engine Pistons, Rings and Connecting Rods
G3500H Generator Set Engine Cooling System
C15 and C18 On-Highway Engines Engine Oil Filter Base - Remove and Install - C15
G3500H Generator Set Engine Lubrication System
G3500H Generator Set Engine Valve System Components
C15 and C18 On-Highway Engines Engine Oil Filter Base - Remove and Install - C18
G3500H Generator Set Engine Air/Fuel Ratio Control - NO<SUB>X</SUB> Feedback
2014/03/07 New Engine Software Is Now Used for Certain Industrial and Generator Set C9 Engines {1901, 1902, 1920}
2013/11/13 New Exhaust Temperature Sensor Groups Are Used on Certain 3500, 3600, C175, and C280 Marine and Petroleum Off-Shore Applications {1408, 1900, 1906, 1919, 1921, 1922, 1928, 1929, 7498}
C15 and C18 On-Highway Engines Engine Oil Cooler - Remove and Install - C15
C15 and C18 On-Highway Engines Engine Oil Cooler - Remove and Install - C18
C280-08 Marine Engine After Stopping Engine
2013/11/13 A New Alternator and Alternator Bracket Have Been Introduced on Certain C4.4 and C6.6 Engines {1405, 1425}
Reuse and Salvage for Engine Dampers {1202, 1205} Reuse and Salvage for Engine Dampers {1202, 1205}
C15 and C18 On-Highway Engines Engine Oil Pump - Remove and Install
2014/02/20 New Anti Drift Valves are Now Used on Certain 345D and 349D Excavators {5059}
C280-16 Engine Alternator - Replace
CX31-P600 Petroleum Transmission Visual Inspection
CX31-P600 Petroleum Transmission Torque Converter Troubleshooting
C15 and C18 On-Highway Engines Water Temperature Regulator Housing - Remove and Install
CX31-P600 Petroleum Transmission Transmission Planetary Troubleshooting
C15 and C18 On-Highway Engines Flywheel - Remove and Install
CX31-P600 Petroleum Transmission Hydraulic Oil Contamination - Test
C280 Marine Engines Battery