Water Temperature Regulator Housing - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 207-1601     | 橡胶润滑剂     | 1     |
B     | 221-8647     | 油封安装工具     |     |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 将冷却液从冷却系统中排入合适的容器,以便保存或弃置。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"以了解正确的排放和加注步骤。
- 拆下管组件 (1) 。
Show/hide table
图 1 | g02160354 |
- 拆下螺栓 (3) 和夹子。
- 断开线束组件 (4) 。
- 卸下螺栓 (5) 。
- 拆下水温调节器壳体 (2) 。
- 拆下螺栓 (6) ,然后拆下壳体 (7) 。
Show/hide table
图 2 | g02827396 |
- 拆下管 (9) ,然后拆下 O 形密封圈 (8) 。
- 拆下并废弃密封件 (11) 。 拆下水温调节器 (10) 。
Show/hide table
图 3 | g02827479 |
- 拆下唇形密封 (12) 。 记下唇形密封的方位,以便于安装。
Show/hide table
图 4 | g02827497 |
安装步骤
- 按与拆卸相反的顺序安装水温调节器壳体 (2) 。
- 将工具 (A) 涂抹到唇形密封 (12) 的密封圈表面上。 使用工具 (B) 安装唇形密封 (12) 。
- 将工具 (A) 涂抹到 O 形密封圈 (8) 和管组件 (1) 上。
- 将水温传感器 (2) 上紧到 20 ± 3 N·m (177 ± 27 lb in) 的扭矩。
Caterpillar Information System:
CX31-P600 Petroleum Transmission Torque Converter Troubleshooting
CX31-P600 Petroleum Transmission Visual Inspection
C280-16 Engine Alternator - Replace
2014/02/20 New Anti Drift Valves are Now Used on Certain 345D and 349D Excavators {5059}
C15 and C18 On-Highway Engines Engine Oil Pump - Remove and Install
Reuse and Salvage for Engine Dampers {1202, 1205} Reuse and Salvage for Engine Dampers {1202, 1205}
2013/11/13 A New Alternator and Alternator Bracket Have Been Introduced on Certain C4.4 and C6.6 Engines {1405, 1425}
G3500H Generator Set Engine Electric Starting System
G3500H Generator Set Engine Pistons, Rings and Connecting Rods
G3500H Generator Set Engine Cooling System
C15 and C18 On-Highway Engines Engine Oil Filter Base - Remove and Install - C15
G3500H Generator Set Engine Lubrication System
CX31-P600 Petroleum Transmission Transmission Planetary Troubleshooting
C15 and C18 On-Highway Engines Flywheel - Remove and Install
CX31-P600 Petroleum Transmission Hydraulic Oil Contamination - Test
C280 Marine Engines Battery
C15 and C18 On-Highway Engines Flywheel Housing - Remove and Install - Power Take Off equipped
C15 and C18 On-Highway Engines Power Take-Off Drive Group - Assemble
C15 and C18 On-Highway Engines Crankshaft Front Seal - Remove and Install
Exhaust Leaks May Cause Failures of the 195-2431 Detonation Sensor Groups on Certain G3500 Engines{1408, 7400} Exhaust Leaks May Cause Failures of the 195-2431 Detonation Sensor Groups on Certain G3500 Engines{1408, 7400}
C15 and C18 On-Highway Engines Rocker Arm and Shaft - Remove and Install
C15 and C18 On-Highway Engines Cylinder Head - Remove and Install
C280-16 Engine Exhaust Manifold Shield - Remove and Install
3516C Marine Engine Catalyst (SCR) - Replace