Power Take-Off Drive Group - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺柱 (5/8 - 18 x 8 in)     |
2     |
B     | 1P-0520     | 冲头总成     | 2     |
C     | 9S-3263     | 螺纹锁固胶     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 利用工具 (B) 将套筒轴承 (13) 装入飞轮壳中。 套筒轴承中槽口的位置应保持角度 (Y) ,即距水平中心线 15 ± 1 度。 轴承应当安装到深度 (Z) ,即 2.0 ± 0.5 mm (0.080 ± 0.020 in)。
Show/hide table
图 1 | g01106888 |
- 利用工具 (B) 将套筒轴承 (12) 装入飞轮壳中。 套筒轴承中槽口的位置应保持角度 (X) ,即距竖直中心线 15 ± 1 度。 轴承应当安装到深度 (Z) ,即 2.0 ± 0.5 mm (0.080 ± 0.020 in)。
- 将 O 形密封圈安装在盖 (11) 上。 将盖 (11) 和螺栓安装在飞轮壳体的背面。
- 将齿轮组件 (9) 和齿轮组件 (10) 安置在飞轮壳体中。
Show/hide table
图 2 | g01106649 |
- 利用工具 (B) 将套筒轴承 (3) 装入转接接头 (2) 中。 在接头 (2) 上安装O形密封圈。
Show/hide table
图 3 | g01106948 |
- 将套筒轴承内的溢油槽与惰齿轮 (6) 内的溢油槽对齐。 利用工具 (B) 将套筒轴承装入惰齿轮 (6) 中。
Show/hide table
图 4 | g01106976 |
- 定位惰齿轮 (6) 和护圈 (5) 。 安装螺栓 (4) 。
- 将套筒轴承内的溢油槽与惰齿轮 (7) 内的溢油槽对齐。 利用工具 (B) 将套筒轴承装入惰齿轮 (7) 中。
- 定位惰齿轮 (7) 和护圈 (5) 。 安装螺栓 (4) 。
- 将 O 形密封圈装入曲轴齿轮 (8) 的沉孔中。 用清洁的发动机机油润滑 O 形密封圈。 将曲轴齿轮 (8) 安装到工具 (A) 上。
- 将转接接头 (2) 定位到飞轮壳上。 将工具 (C) 涂抹在螺栓 (1) 的螺纹上后安装螺栓。
End By: 安装飞轮。
Caterpillar Information System:
C15 and C18 On-Highway Engines Flywheel Housing - Remove and Install - Power Take Off equipped
C280 Marine Engines Battery
CX31-P600 Petroleum Transmission Hydraulic Oil Contamination - Test
C15 and C18 On-Highway Engines Flywheel - Remove and Install
CX31-P600 Petroleum Transmission Transmission Planetary Troubleshooting
C15 and C18 On-Highway Engines Water Temperature Regulator Housing - Remove and Install
CX31-P600 Petroleum Transmission Torque Converter Troubleshooting
CX31-P600 Petroleum Transmission Visual Inspection
C280-16 Engine Alternator - Replace
2014/02/20 New Anti Drift Valves are Now Used on Certain 345D and 349D Excavators {5059}
C15 and C18 On-Highway Engines Engine Oil Pump - Remove and Install
Reuse and Salvage for Engine Dampers {1202, 1205} Reuse and Salvage for Engine Dampers {1202, 1205}
C15 and C18 On-Highway Engines Crankshaft Front Seal - Remove and Install
Exhaust Leaks May Cause Failures of the 195-2431 Detonation Sensor Groups on Certain G3500 Engines{1408, 7400} Exhaust Leaks May Cause Failures of the 195-2431 Detonation Sensor Groups on Certain G3500 Engines{1408, 7400}
C15 and C18 On-Highway Engines Rocker Arm and Shaft - Remove and Install
C15 and C18 On-Highway Engines Cylinder Head - Remove and Install
C280-16 Engine Exhaust Manifold Shield - Remove and Install
3516C Marine Engine Catalyst (SCR) - Replace
Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479} Procedure for Installing the 450-6188 Solenoid Valve Gp and 450-3897 Wiring Harness on G3500 Petroleum Engines{5479}
2013/12/19 New Software Is Used on Certain C32 Marine Engines {1901, 1920}
3516C Marine Engine Model View Illustrations
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C15 and C18 On-Highway Engines Camshaft - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Water in Fuel - Test