Rear Power Take-Off (RPTO) - Remove
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | - | Guide Stud (M 12 X 1.75 by 6 inch) |
2 |
| B | 1P-0520 | Driver Group | 1 |
| C | 156-7100 | Puller Group | 1 |
Start By:
- Remove the crankshaft rear seal.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| |
| Illustration 1 | g01103652 |
- Install Tooling (A) in the crankshaft through crankshaft gear (17).
- Remove bolts (23), cover (22), and gasket (21). Remove crankshaft gear (17) from the crankshaft. Remove seal (16).
- Remove bolts (19), bolt (20), idler shaft (18), and idler gear (14).
- Remove bearing (15) from idler gear (14) with Tooling (B).
- Remove lip seal (12), bolts (11), and adapter assembly (10). Remove O-ring seal (9), dowels (8), thrust washer (7), and bearing (6) from adapter assembly (10).
- Remove PTO shaft (5) from flywheel housing (4). Remove dowel (13).
- Remove thrust washer (2) and dowels (1).
- Remove bearing (3) with Tooling (C).
Caterpillar Information System:
C9.3 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C9.3 Engines for Caterpillar Built Machines Water Pump - Assemble
797B Off-Highway Truck Main Drive Shaft Universal Joint - Inspect
C9.3 Engines for Caterpillar Built Machines Water Pump - Disassemble
C13, C15, and C18 Tier 4 Final Engines Water Pump
C13, C15, and C18 Tier 4 Final Engines Valve Rocker Arm
C13, C15, and C18 Tier 4 Final Engines Air Lines
C13, C15, and C18 Tier 4 Final Engines Engine Support (Front)
C9.3 Engines for Caterpillar Built Machines Water Pump - Remove and Install
C9.3 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
G3500H Generator Set Engine Speed/Timing - Test
C9.3 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Install
C32 Marine Generator Set Overhaul Considerations
2013/03/29 An Improved Torque Sequence Is Used on Certain C18 Marine Engine Valve Covers {1107}
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Relief Valve (Cold Start) - Test
C9.3 Engines for Caterpillar Built Machines Compression Brake - Disassemble - Valve Assembly
C9.3 Engines for Caterpillar Built Machines Compression Brake - Assemble - Valve Assembly
2013/04/22 A New Exhaust Shield Group is Available for a G3516B Engine {1067}
C13, C15, and C18 Tier 4 Final Engines Exhaust Manifold
C15 and C18 Engines for Caterpillar Built Machines Exhaust Manifold
C13, C15, and C18 Tier 4 Final Engines Turbocharger
C4.4 and C7.1 Engines Data Link - Test