Water Pump - Assemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-0510 | Driver Gp | 1 |
B | 5P-9722 | Seal Driver | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) and a suitable press to install hub (8) on shaft assembly (7).
- Use Tooling (A) and a suitable press to install shaft (7) into housing (6). Install the shaft assembly until the bearing is flush with the housing.
- Use Tooling (B) and a suitable press to install seal assembly (5) in housing (6). The operating Height (C) of seal assembly (5) is
12.19 ± 0.13 mm (0.480 ± 0.005 inch) . - Use Tooling (A) and a suitable press to install impeller (4) onto shaft assembly (7). The operating height (D) of impeller (4) is
8.97 ± 0.25 mm (0.350 ± 0.010 inch) . - Install new gasket (3).
- Position cover (2) and install bolts (1).
- Position pulley (9) and install bolts (10). The distance (E) from the inside groove of the water pump pulley to the face of the housing should be
136.40 ± 0.300 mm (5.370 ± 0.012 inch) . - Refer to Specifications, "Water Pump" for the tolerances.
Show/hide table
Illustration 1 | g01358794 |
Show/hide table
Illustration 2 | g01359145 |
Tolerances |
End By:
- Install the water pump.
Caterpillar Information System:
797B Off-Highway Truck Main Drive Shaft Universal Joint - Inspect
C9.3 Engines for Caterpillar Built Machines Water Pump - Disassemble
C13, C15, and C18 Tier 4 Final Engines Water Pump
C13, C15, and C18 Tier 4 Final Engines Valve Rocker Arm
C13, C15, and C18 Tier 4 Final Engines Air Lines
C13, C15, and C18 Tier 4 Final Engines Engine Support (Front)
C9.3 Engines for Caterpillar Built Machines Water Pump - Remove and Install
C9.3 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C9.3 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C9.3 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C9.3 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Remove
G3500H Generator Set Engine Speed/Timing - Test
C9.3 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Install
C32 Marine Generator Set Overhaul Considerations
2013/03/29 An Improved Torque Sequence Is Used on Certain C18 Marine Engine Valve Covers {1107}
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Relief Valve (Cold Start) - Test
C9.3 Engines for Caterpillar Built Machines Compression Brake - Disassemble - Valve Assembly
C9.3 Engines for Caterpillar Built Machines Compression Brake - Assemble - Valve Assembly
2013/04/22 A New Exhaust Shield Group is Available for a G3516B Engine {1067}
C13, C15, and C18 Tier 4 Final Engines Exhaust Manifold
C15 and C18 Engines for Caterpillar Built Machines Exhaust Manifold