Inlet and Exhaust Valve Seat Inserts - Remove and Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 9S-3095 | Puller Handle | 1 |
| B | 6V-4194
(1) |
Valve Seat Extractor | 1 |
| 1U-9167
(2) |
Valve Seat Extractor | 1 | |
Show/hide table
| (1) | For use with Exhaust Valve Seat |
| (2) | For use with Intake Valve Seat |
Start By:
- Remove inlet and exhaust valves.
- Use Tooling (A) and Tooling (B) to remove valve seat inserts (1).
Show/hide table
| |
| Illustration 1 | g01137634 |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| C | 4C-6372(1) | Valve Seat Driver | 1 |
| 364-4009(2) | Valve Seat Driver | 1 | |
Show/hide table
| (1) | For use with Exhaust Valve Seat |
| (2) | For use with Intake Valve Seat |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Lower the temperature of new valve seat inserts (1). Use Tooling (C) to install valve seat inserts (1) into the cylinder head.
Show/hide table
| |
| Illustration 2 | g01137637 |
Note: Do not machine the prefinished valve seat inserts in order to correct the valve stem projection. An excessive valve stem projection indicates that the valve seat insert is not seated or material was not cleaned from the bottom of the counterbore.
End By:
- Install the inlet and exhaust valves.
Caterpillar Information System:
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C9.3 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C9.3 Engines for Caterpillar Built Machines Turbocharger - Remove and Install - Cooled by Coolant
2013/04/04 An Additional Spacer Is Now Used in the Crankshaft Pulley Group of Certain C7 and C9 Marine Engines {1205}
C3.3B Tier 4 Final Engines for Caterpillar Built Machines Exhaust Manifold
C15 and C18 Engines Engine Oil and Filter - Change
C3.3B Tier 4 Final Engines for Caterpillar Built Machines Crankcase Breather
C3.3B Tier 4 Final Engines for Caterpillar Built Machines Engine Oil Pan
2013/05/28 New Flywheel Housing Assemblies and Gasket Are Used on Certain Marine and Petroleum 3500 Engines {1157, 7555}
C7.1 Marine Engine Generator - Remove and Install
C4.4 and C7.1 Engines CAN Data Link - Test
C9.3 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C9.3 Engines for Caterpillar Built Machines Water Pump - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Engine Support (Front)
C13, C15, and C18 Tier 4 Final Engines Air Lines
C13, C15, and C18 Tier 4 Final Engines Valve Rocker Arm
C13, C15, and C18 Tier 4 Final Engines Water Pump
C9.3 Engines for Caterpillar Built Machines Water Pump - Disassemble
797B Off-Highway Truck Main Drive Shaft Universal Joint - Inspect
C9.3 Engines for Caterpillar Built Machines Water Pump - Assemble
C9.3 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C9.3 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Remove
G3500H Generator Set Engine Speed/Timing - Test