Flywheel Housing - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7575 | Link Bracket | 2 |
Start By:
- Remove the flywheel.
- Fasten Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of flywheel housing (1) is approximately
25 kg (55 lb) . - Remove bolts (2).
- Remove bolts (3) (not shown) that fasten the engine oil pan to flywheel housing (1). Remove flywheel housing (1).
Show/hide table
Illustration 1 | g01138072 |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7575 | Link Bracket | 2 |
B | 1U-8846 | Gasket Sealant | 1 |
- Apply Tooling (B) to the entire mounting surface of the flywheel housing prior to installation.
Show/hide table
Illustration 2 g01138072 - Fasten Tooling (A) and a suitable lifting device to flywheel housing (1). The weight of flywheel housing (1) is approximately
25 kg (55 lb) . Position flywheel housing (1) on the engine block. - Install bolts (2).
- Install bolts (3) (not shown) that fasten the engine oil pan to flywheel housing (1).
End By:
- Install the flywheel.
Caterpillar Information System:
C9.3 Engines for Caterpillar Built Machines Water Pump - Assemble
797B Off-Highway Truck Main Drive Shaft Universal Joint - Inspect
C9.3 Engines for Caterpillar Built Machines Water Pump - Disassemble
C13, C15, and C18 Tier 4 Final Engines Water Pump
C13, C15, and C18 Tier 4 Final Engines Valve Rocker Arm
C13, C15, and C18 Tier 4 Final Engines Air Lines
C13, C15, and C18 Tier 4 Final Engines Engine Support (Front)
C9.3 Engines for Caterpillar Built Machines Water Pump - Remove and Install
C9.3 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
C9.3 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C9.3 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Remove
G3500H Generator Set Engine Speed/Timing - Test
C9.3 Engines for Caterpillar Built Machines Rear Power Take-Off (RPTO) - Install
C32 Marine Generator Set Overhaul Considerations
2013/03/29 An Improved Torque Sequence Is Used on Certain C18 Marine Engine Valve Covers {1107}
777F, 777G, and 785D OEM Off-Highway Truck/Tractors Water Delivery System Relief Valve (Cold Start) - Test
C9.3 Engines for Caterpillar Built Machines Compression Brake - Disassemble - Valve Assembly
C9.3 Engines for Caterpillar Built Machines Compression Brake - Assemble - Valve Assembly
2013/04/22 A New Exhaust Shield Group is Available for a G3516B Engine {1067}
C13, C15, and C18 Tier 4 Final Engines Exhaust Manifold
C15 and C18 Engines for Caterpillar Built Machines Exhaust Manifold
C13, C15, and C18 Tier 4 Final Engines Turbocharger