Alternator - Install
- 如有必要,按照步骤 1.a 至步骤 1.c 将交流发电机的支架安装到缸盖上。
- 将支架 (11) 定位到缸盖上,使箭头和字样 UP(向上)处于垂直位置。
- 将螺栓 (10) 安装到支架 (11) 上,用手拧紧。
- 拧紧螺栓 (10) 至扭矩为
44 N·m (32 lb ft) 。
Show/hide table图 2 g02711217 - 如有必要,按照步骤 2.a 至步骤 2.b 安装交流发电机的皮带轮。
注: 这种方法不适用于一些皮带轮配置类型。
- 将皮带轮 (4) 和螺母 (5)(未显示)安装到交流发电机 (2) 的轴上。
- 使用内六角板手固定交流发电机的轴。 使用带柄的梅花扳手拧紧螺母 (5)(未显示)。 拧紧螺母至扭矩为
80 N·m (59 lb ft) 。
- 将交流发电机 (2) 安装到交流发电机的支架上。 将螺栓 (3) 安装到交流发电机 (2) 上。
- 将螺母 (1) 安装到螺栓 (3) 上,用手拧紧。.
- 安装支架 (9),然后将螺栓和垫片 (6) 安装到交流发电机 (2) 上,用手拧紧。
- 安装螺栓 (8) 和螺母 (7),用手拧紧。
- 安装 V 形皮带。 有关正确的步骤,请参阅拆解和组装, "V 形皮带 - 拆卸和安装"。
- 拧紧螺母 (1) 和螺栓 (3) 至扭矩为
22 N·m (195 lb in) 。 - 拧紧螺栓和垫片 (6) 至扭矩为
22 N·m (195 lb in) 。 - 拧紧螺母 (7) 和螺栓 (8) 至扭矩为
44 N·m (32 lb ft) 。 - 将线束组件连接到交流发电机 (2) 上。
- 将蓄电池断路开关转到接通位置。
Show/hide table
图 1 | g02711220 |
Caterpillar Information System:
C7.1 (Mech) Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C175-16 and C175-20 Generator Set Engines Pressure Control Valve - Oil Regulator Valve and Oil Bypass Valve
PMG3516 Power Module Coolant Temperature Regulator - Replace
169-3374 Brass Injector Sleeve Removal Group for 3176 and 3176B Engines{0374, 0599, 0700, 0706} 169-3374 Brass Injector Sleeve Removal Group for 3176 and 3176B Engines{0374, 0599, 0700, 0706}
NEHS0733: 159-9404 Counterbore Tool Group For C10 through C13 {0705} NEHS0733: 159-9404 Counterbore Tool Group For C10 through C13 {0705}
PMG3516 Power Module Engine Air Cleaner Service Indicator - Inspect
PMG3516 Power Module Fluid Recommendations
PMG3516 Power Module Refill Capacities
PMG3516 Power Module Product Lifting
PMG3516 Power Module Product Description
3512B and 3512C Petroleum Generator Set Engines Crankcase Pressure Is High
C175-16 Marine Propulsion Engines Sensor Signal (Analog, Active) - Test
C7.1 (Mech) Industrial Engine Alternator - Remove
C7.1 (Mech) Industrial Engine Camshaft - Remove and Install
C7.1 (Mech) Industrial Engine Camshaft Bearings - Remove and Install
C7.1 (Mech) Industrial Engine Camshaft Gear - Remove and Install
C7.1 (Mech) Industrial Engine Connecting Rod Bearings - Install - Connecting Rods in Position
C7.1 (Mech) Industrial Engine Connecting Rod Bearings - Remove - Connecting Rods in Position
C7.1 (Mech) Industrial Engine Crankcase Breather - Install - Filtered Breather
C7.1 (Mech) Industrial Engine Crankcase Breather - Remove - Filtered Breather
C7.1 (Mech) Industrial Engine Crankcase Breather - Install - Unfiltered Breather
C7.1 (Mech) Industrial Engine Crankcase Breather - Remove - Unfiltered Breather
C7.1 (Mech) Industrial Engine Crankshaft - Install
C7.1 (Mech) Industrial Engine Crankshaft - Remove