Crankcase Breather - Remove - Filtered Breather
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 拆下呼吸器的滤罐 (10)。 请参阅操作和保养手册, "曲轴箱呼吸器(滤罐)- 更换"。
- 松开卡箍 (2) 和 (4)。
- 从气门机构盖 (1) 和曲轴箱呼吸器的滤清器座 (5) 上拆下软管 (3)。
- 松开卡箍 (9) ,然后从曲轴箱呼吸器的滤清器座 (5) 上断开软管组件 (11)。
- 卸下螺栓 (6),然后从安装支架 (7) 上拆下曲轴箱呼吸器的滤清器座 (5)。
- 如有必要,按照步骤 6.a 至步骤 6.b 从缸盖上卸下安装支架 (8)。
- 从安装支架 (8) 上卸下螺栓 (7)。
- 从缸盖上卸下安装支架 (8)。
Show/hide table
图 1 | g02728043 |
Caterpillar Information System:
C7.1 (Mech) Industrial Engine Crankcase Breather - Install - Filtered Breather
C7.1 (Mech) Industrial Engine Connecting Rod Bearings - Remove - Connecting Rods in Position
C7.1 (Mech) Industrial Engine Connecting Rod Bearings - Install - Connecting Rods in Position
C7.1 (Mech) Industrial Engine Camshaft Gear - Remove and Install
C7.1 (Mech) Industrial Engine Camshaft Bearings - Remove and Install
C7.1 (Mech) Industrial Engine Camshaft - Remove and Install
C7.1 (Mech) Industrial Engine Alternator - Remove
C7.1 (Mech) Industrial Engine Alternator - Install
C7.1 (Mech) Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C175-16 and C175-20 Generator Set Engines Pressure Control Valve - Oil Regulator Valve and Oil Bypass Valve
PMG3516 Power Module Coolant Temperature Regulator - Replace
169-3374 Brass Injector Sleeve Removal Group for 3176 and 3176B Engines{0374, 0599, 0700, 0706} 169-3374 Brass Injector Sleeve Removal Group for 3176 and 3176B Engines{0374, 0599, 0700, 0706}
C7.1 (Mech) Industrial Engine Crankcase Breather - Install - Unfiltered Breather
C7.1 (Mech) Industrial Engine Crankcase Breather - Remove - Unfiltered Breather
C7.1 (Mech) Industrial Engine Crankshaft - Install
C7.1 (Mech) Industrial Engine Crankshaft - Remove
C7.1 (Mech) Industrial Engine Crankshaft Front Seal - Remove and Install
C7.1 (Mech) Industrial Engine Crankshaft Gear - Remove and Install
C7.1 (Mech) Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C7.1 (Mech) Industrial Engine Crankshaft Rear Seal - Install
C7.1 (Mech) Industrial Engine Crankshaft Rear Seal - Remove
C7.1 (Mech) Industrial Engine Cylinder Head - Install
C7.1 (Mech) Industrial Engine Cylinder Head - Remove
C7.1 (Mech) Industrial Engine Electric Starting Motor - Remove and Install