Camshaft Bearings - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 8S-2241 | 凸轮轴轴承工具总成 | 1 |
B | 8H-0684 | 棘轮扳手 | 1 |
开始:
- 拆下发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 拆卸"。
- 拆下凸轮轴。 请参阅拆解和组装, "凸轮轴 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 检查凸轮轴轴承 (1)。 有关更多资料,请参阅技术参数, "凸轮轴轴承"。
- 如果凸轮轴轴承 (1) 磨损或损坏,使用工具 (A) 和工具 (B) 将凸轮轴轴承从缸体上拆下。
注: 将凸轮轴轴承从缸体前部拆下。
Show/hide table
图 1 | g01340581 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 8S-2241 | 凸轮轴轴承工具总成 | 1 |
B | 8H-0684 | 棘轮扳手 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 清洁缸体中的轴承壳体。 确保轴承壳体的油孔中没有碎屑。
Show/hide table
图 2 g01340583 - 使用清洁的发动机机油润滑缸体中的轴承壳体。
- 准确地对准凸轮轴轴承 (1) 上的大油孔 (X) 与缸体上的油孔。
注: 凸轮轴轴承中的凹槽 (Y) 必须处于缸体顶部。
- 使用工具 (A) 和工具 (B) 将凸轮轴轴承 (1) 安装到缸体中。 安装凸轮轴轴承,使轴承前沿与缸体中的凹槽面平齐。
注: 确保已将所有油孔正确对准。 如果没有正确对准油孔,应拆卸凸轮轴轴承。
结束:
- 安装凸轮轴。 请参阅拆解和组装, "凸轮轴 - 拆卸和安装"。
- 安装发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
C7.1 (Mech) Industrial Engine Camshaft - Remove and Install
C7.1 (Mech) Industrial Engine Alternator - Remove
C7.1 (Mech) Industrial Engine Alternator - Install
C7.1 (Mech) Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C175-16 and C175-20 Generator Set Engines Pressure Control Valve - Oil Regulator Valve and Oil Bypass Valve
PMG3516 Power Module Coolant Temperature Regulator - Replace
169-3374 Brass Injector Sleeve Removal Group for 3176 and 3176B Engines{0374, 0599, 0700, 0706} 169-3374 Brass Injector Sleeve Removal Group for 3176 and 3176B Engines{0374, 0599, 0700, 0706}
NEHS0733: 159-9404 Counterbore Tool Group For C10 through C13 {0705} NEHS0733: 159-9404 Counterbore Tool Group For C10 through C13 {0705}
PMG3516 Power Module Engine Air Cleaner Service Indicator - Inspect
PMG3516 Power Module Fluid Recommendations
PMG3516 Power Module Refill Capacities
PMG3516 Power Module Product Lifting
C7.1 (Mech) Industrial Engine Camshaft Gear - Remove and Install
C7.1 (Mech) Industrial Engine Connecting Rod Bearings - Install - Connecting Rods in Position
C7.1 (Mech) Industrial Engine Connecting Rod Bearings - Remove - Connecting Rods in Position
C7.1 (Mech) Industrial Engine Crankcase Breather - Install - Filtered Breather
C7.1 (Mech) Industrial Engine Crankcase Breather - Remove - Filtered Breather
C7.1 (Mech) Industrial Engine Crankcase Breather - Install - Unfiltered Breather
C7.1 (Mech) Industrial Engine Crankcase Breather - Remove - Unfiltered Breather
C7.1 (Mech) Industrial Engine Crankshaft - Install
C7.1 (Mech) Industrial Engine Crankshaft - Remove
C7.1 (Mech) Industrial Engine Crankshaft Front Seal - Remove and Install
C7.1 (Mech) Industrial Engine Crankshaft Gear - Remove and Install
C7.1 (Mech) Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in Position