Camshaft - Remove and Install
开始:
- 拆下注油泵。 有关正确的步骤,请参阅拆解和组装, "燃油注油泵(机械)- 拆卸和安装"。
- 拆下摇臂轴和推杆。 有关正确步骤,请参阅拆解和组装, "摇臂轴和推杆 - 拆卸"。
- 拆卸前壳体。 有关正确的步骤,请参阅拆解和组装, "壳体(前)- 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 应将发动机倒置安装在适当的台架上。
Show/hide table
图 1 g02009034 - 将止推垫圈 (1) 从缸体上拆下。 除非定位销损坏,否则不要从缸体上卸下定位销 (2)。
注: 止推垫圈可能有一个或两个槽 (X)。
Show/hide table图 2 g02711850 Show/hide table注意 拆卸或安装凸轮轴时不要损坏凸轮或轴承。
- 小心地将凸轮轴 (3) 从缸体上卸下。
- 如有必要,将键 (4) 从凸轮轴 (3) 上卸下。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 清洁凸轮轴和止推垫圈。 检查凸轮轴和止推垫圈是否磨损和损坏。 更多资料,请参阅技术规格, "凸轮轴"。 更换任何磨损或损坏的部件。
- 清洁缸体中的凸轮轴轴承。 检查凸轮轴轴承是否磨损和损坏。 有关更多资料,请参阅技术参数, "凸轮轴轴承"。 如有必要,更换凸轮轴轴承。 请参阅拆解和组装, "凸轮轴轴承 - 拆卸和安装",以了解正确的程序。
Show/hide table
注意 强烈推荐应在安装新凸轮轴时更换所有的挺杆。
- 检查挺杆有无磨损和损坏。 更多信息请参阅技术参数, "挺杆总成"。 更换所有磨损或损坏的挺杆。 请参阅拆解和组装, "挺杆总成 - 拆卸和安装",以了解正确的程序。
Show/hide table
图 3 g02711850 - 如有必要,将新键 (4) 安装到凸轮轴 (3) 上。
- 使用清洁的发动机机油润滑凸轮轴 (3) 的轴承面和凸轮轴的凸轮。
Show/hide table
注意 拆卸或安装凸轮轴时不要损坏凸轮或轴承。
- 小心地将凸轮轴 (3) 安装到缸体中。
Show/hide table
图 4 g02009034 - 用清洁的发动机机油润滑止推垫圈。 对齐止推垫圈 (1) 中的槽 (X) 与缸体中的定位销 (2)。 将止推垫圈 (1) 安装到缸体的凹槽中。
注: 止推垫圈可能有一个或两个槽 (X)。
结束:
- 安装前壳体。 有关正确的步骤,请参阅拆解和组装, "壳体(前)- 安装"。
- 安装摇臂轴和推杆。 有关正确步骤,请参阅拆解和组装, "摇臂轴和推杆 - 安装"。
- 安装注油泵。 有关正确的步骤,请参阅拆解和组装, "燃油注油泵(机械)- 拆卸和安装"。
Caterpillar Information System:
C7.1 (Mech) Industrial Engine Alternator - Remove
C7.1 (Mech) Industrial Engine Alternator - Install
C7.1 (Mech) Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C175-16 and C175-20 Generator Set Engines Pressure Control Valve - Oil Regulator Valve and Oil Bypass Valve
PMG3516 Power Module Coolant Temperature Regulator - Replace
169-3374 Brass Injector Sleeve Removal Group for 3176 and 3176B Engines{0374, 0599, 0700, 0706} 169-3374 Brass Injector Sleeve Removal Group for 3176 and 3176B Engines{0374, 0599, 0700, 0706}
NEHS0733: 159-9404 Counterbore Tool Group For C10 through C13 {0705} NEHS0733: 159-9404 Counterbore Tool Group For C10 through C13 {0705}
PMG3516 Power Module Engine Air Cleaner Service Indicator - Inspect
PMG3516 Power Module Fluid Recommendations
PMG3516 Power Module Refill Capacities
PMG3516 Power Module Product Lifting
PMG3516 Power Module Product Description
C7.1 (Mech) Industrial Engine Camshaft Bearings - Remove and Install
C7.1 (Mech) Industrial Engine Camshaft Gear - Remove and Install
C7.1 (Mech) Industrial Engine Connecting Rod Bearings - Install - Connecting Rods in Position
C7.1 (Mech) Industrial Engine Connecting Rod Bearings - Remove - Connecting Rods in Position
C7.1 (Mech) Industrial Engine Crankcase Breather - Install - Filtered Breather
C7.1 (Mech) Industrial Engine Crankcase Breather - Remove - Filtered Breather
C7.1 (Mech) Industrial Engine Crankcase Breather - Install - Unfiltered Breather
C7.1 (Mech) Industrial Engine Crankcase Breather - Remove - Unfiltered Breather
C7.1 (Mech) Industrial Engine Crankshaft - Install
C7.1 (Mech) Industrial Engine Crankshaft - Remove
C7.1 (Mech) Industrial Engine Crankshaft Front Seal - Remove and Install
C7.1 (Mech) Industrial Engine Crankshaft Gear - Remove and Install