Connecting Rod Bearings - Remove - Connecting Rods in Position
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A(1) | 9U-6198 | 曲轴转动工具 | 1 |
A(2) | 9U-7336 | 壳体 | 1 |
5P-7305 | 发动机盘车工具 | 1 | |
B | 227-4390 | E12 梅花套筒 | 1 |
Show/hide table
(1) | 曲轴转动工具用于前皮带轮。 |
(2) | 该工具在电动起动马达的孔上使用。 |
开始:
- 拆下发动机机油泵。 有关正确的步骤,请参阅拆解和组装, "发动机机油泵 - 拆卸"。
注: 可以使用两个工具 (A) 中的任意一个。 请使用最适用的工具。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
废弃所有旧的连杆紧固件。 |
注: 如果需要更换所有连杆轴承,可以同时在两个气缸上进行本程序。 本程序可在下列气缸配对上同时进行。 1 和 6, 2和 5 和 3 和 4。 确保在从一对气缸换到另一对气缸之前安装完两对连杆轴承。 有关正确的步骤,请参阅拆解和组装, "连杆轴承 - 安装"。
- 使用工具 (A) 转动曲轴,使曲轴销在下止点位置。
如有必要,拆卸电热塞。 有关正确的步骤,请参阅拆解和组装, "电热塞 - 拆卸和安装"。
注: 拆卸电热塞有助于卸下连杆轴承。 并不是一定要拆下电热塞。
Show/hide table图 1 g02319916 位置 (X) 中的蚀刻编号 Show/hide table图 2 g01341322 - 连杆和连杆盖在位置 (X) 中应有蚀刻编号。 连杆和连杆盖上的编号必须相互匹配。 如有必要,在连杆 (5) 和连杆盖 (2) 上作一个临时标记来识别气缸编号。
注: 不要在断面分裂式连杆上冲出识别标记。 不要在断面分裂式连杆上压印识别标记。
- 使用工具 (B) 拆下螺栓 (1)。 弃置螺栓 (1)。
- 将连杆盖 (2) 从连杆 (5) 上拆下。
- 将下轴瓦 (3) 从连杆盖 (2) 上拆下。 保持轴瓦与连杆盖一体。
- 小心地将连杆 (5) 推入缸孔中,直到连杆 (5) 离开曲轴。 将上轴瓦 (4) 从连杆上拆下。 保持轴瓦一体。
注: 不要推压连杆的断面分裂面,否则会导致损坏。 不要使连杆接触活塞冷却喷嘴。
- 重复步骤 1 到步骤 6,拆卸其余的轴瓦。
注: 放置断面分裂式连杆时必须要安装连杆盖。 在完成轴瓦的拆卸程序后,立即进行安装程序。 有关正确的步骤,请参阅拆解和组装, "连杆轴承 - 安装"。
Caterpillar Information System:
C7.1 (Mech) Industrial Engine Connecting Rod Bearings - Install - Connecting Rods in Position
C7.1 (Mech) Industrial Engine Camshaft Gear - Remove and Install
C7.1 (Mech) Industrial Engine Camshaft Bearings - Remove and Install
C7.1 (Mech) Industrial Engine Camshaft - Remove and Install
C7.1 (Mech) Industrial Engine Alternator - Remove
C7.1 (Mech) Industrial Engine Alternator - Install
C7.1 (Mech) Industrial Engine Accessory Drive - Remove and Install - Accessory Drive SAE "A"
C175-16 and C175-20 Generator Set Engines Pressure Control Valve - Oil Regulator Valve and Oil Bypass Valve
PMG3516 Power Module Coolant Temperature Regulator - Replace
169-3374 Brass Injector Sleeve Removal Group for 3176 and 3176B Engines{0374, 0599, 0700, 0706} 169-3374 Brass Injector Sleeve Removal Group for 3176 and 3176B Engines{0374, 0599, 0700, 0706}
NEHS0733: 159-9404 Counterbore Tool Group For C10 through C13 {0705} NEHS0733: 159-9404 Counterbore Tool Group For C10 through C13 {0705}
PMG3516 Power Module Engine Air Cleaner Service Indicator - Inspect
C7.1 (Mech) Industrial Engine Crankcase Breather - Install - Filtered Breather
C7.1 (Mech) Industrial Engine Crankcase Breather - Remove - Filtered Breather
C7.1 (Mech) Industrial Engine Crankcase Breather - Install - Unfiltered Breather
C7.1 (Mech) Industrial Engine Crankcase Breather - Remove - Unfiltered Breather
C7.1 (Mech) Industrial Engine Crankshaft - Install
C7.1 (Mech) Industrial Engine Crankshaft - Remove
C7.1 (Mech) Industrial Engine Crankshaft Front Seal - Remove and Install
C7.1 (Mech) Industrial Engine Crankshaft Gear - Remove and Install
C7.1 (Mech) Industrial Engine Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C7.1 (Mech) Industrial Engine Crankshaft Rear Seal - Install
C7.1 (Mech) Industrial Engine Crankshaft Rear Seal - Remove
C7.1 (Mech) Industrial Engine Cylinder Head - Install