Swing Drive Mounting
Show/hide table
Illustration 1 | g02724386 |
Typical example |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
1 | 1 | 5D-1026 Band Clamp | Must assemble bolt clamp head to upper side in order to eliminate potential interference between clamp head and valve. |
Torque to |
Show/hide table
Illustration 2 | g02724387 |
Detailed view of area A Typical example |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
2 | 12 | 461-3882 Bolt | Before assembly, apply Loctite C5A Copper Anti-Seize compound to the threads.
Use the following tightening procedure: 1. Torque to 2. Turn to an additional angle of 45 ± 5 degrees. |
3 | - | - | Before assembly the surfaces must be clean and free of protective coating. |
4 | - | - | Before assemble to upper frame, coat the surfaces with Loctite High Flex GM. |
5 | 1 | 096-4755 Pin | Before assembly, apply Loctite C5A Copper Anti-Seize compound. |
Caterpillar Information System:
3406C Engines for Caterpillar Built Machines Engine Oil Pan
C280 Marine Engines Welding Precaution
C3.4B Engines For Caterpillar Built Machines Inlet Manifold Temperature Sensor - If equipped
C3.4B Engines For Caterpillar Built Machines Boost Pressure Sensor - If equipped
C3.4B Engines For Caterpillar Built Machines Pressure Sensor (NOx Reduction System)
Installation Procedure for the Workover Rig Instrument Panel Kits for C9, C11, C13, and C15 Engines with TH31 / TH35 and CX31 / CX35 Transmissions in 12 Volt and 24 Volt Applications{7451} Installation Procedure for the Workover Rig Instrument Panel Kits for C9, C11, C13, and C15 Engines with TH31 / TH35 and CX31 / CX35 Transmissions in 12 Volt and 24 Volt Applications{7451}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Daily Inspection
2011/10/10 Updated Engine Software Is Now Used for Certain C15 Petroleum Generator Set Engines {1901, 1920}
2011/09/29 A Procedure is Now Used to Install Mounting Blocks for the Auxiliary Lines on Sticks for Certain Excavators {0679, 6502}
Fundamentals of Arc Spray for Reconditioning Components {0679} Fundamentals of Arc Spray for Reconditioning Components {0679}
C3.4B Industrial Engine Balancer
C3.4B Engines For Caterpillar Built Machines Oxygen Sensor
Procedure to Replace Torque Converter Lip Seal on CX31 and CX35 On-Highway Transmissions and CX31-P600 and CX35-P800 Petroleum Transmissions{3105, 7555} Procedure to Replace Torque Converter Lip Seal on CX31 and CX35 On-Highway Transmissions and CX31-P600 and CX35-P800 Petroleum Transmissions{3105, 7555}
C3.4B Industrial Engine Plate Locations and Film Locations - Aftertreatment
284-0415 Bulk Fuel Filtration Group 100 GPM Flow Rate{0680, 0782, 1250, 1280} 284-0415 Bulk Fuel Filtration Group 100 GPM Flow Rate{0680, 0782, 1250, 1280}
2011/10/27 New Information Is Now Available for Modifying the Control Panel Remote Start Circuit Wiring of the Crank Rest Time Delay Relay On C280 Marine Engines {1408, 1451, 7451}
2011/11/21 New Clamping for Water Lines on Certain 3600 and C280 Engines {1380}
3512C and 3516C Marine Auxiliary and Generator Set Engines Product Storage
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Electrical Connectors
C32 Auxiliary Engine Cold Weather Operation
C32 Marine Generator Set Overhaul (Top End)
320D and 323D Excavators Machine System Specifications Front Idler
1U-9001 and 1U-9002 Automatic Hone Tooling{0599, 0677, 0738, 7562, 7562} 1U-9001 and 1U-9002 Automatic Hone Tooling{0599, 0677, 0738, 7562, 7562}
320 GC, 320 and 323 Excavator Machine Systems Specifications Swing Gear and Bearing