Engine Oil Pan
Show/hide table
图 1 | g02724363 |
Show/hide table
107-7378 油底壳总成技术规格 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 1 | 4P-0519 排放接头 | 拧紧至扭矩为 |
2 | 1 | 319-6234 螺塞组件 | 拧紧至扭矩为 |
Show/hide table
图 2 | g02634936 |
Show/hide table
107-7378 油底壳总成技术规格 | |||
项目 | 数量 | 零件 | 技术规格说明 |
- | - | - | 组装发动机油底壳期间使用以下步骤: |
- | - | - | 油底壳的密封表面应没有机油、碎屑、密封垫材料或任何其他密封胶。 |
- | - | - | 油底壳必须在涂抹密封胶的 10 分钟内组装并紧固至缸体。 |
- | - | - | 1. 将 前壳体和缸体前部的连接点。 飞轮壳和缸体后部的连接点。 将一道密封胶涂覆到密封垫或壳体表面。 在 T 形接头位置,胶条应覆盖整个跨度。 |
3 | 31 | 3B-1915 螺栓 | 2. 将螺栓 1 至螺栓 40 按图 2 中所示的数字顺序拧紧至 |
3. 将螺栓 1 至螺栓 40 按图 2 中所示的数字顺序再次拧紧至 |
Caterpillar Information System:
C280 Marine Engines Welding Precaution
C3.4B Engines For Caterpillar Built Machines Inlet Manifold Temperature Sensor - If equipped
C3.4B Engines For Caterpillar Built Machines Boost Pressure Sensor - If equipped
C3.4B Engines For Caterpillar Built Machines Pressure Sensor (NOx Reduction System)
Installation Procedure for the Workover Rig Instrument Panel Kits for C9, C11, C13, and C15 Engines with TH31 / TH35 and CX31 / CX35 Transmissions in 12 Volt and 24 Volt Applications{7451} Installation Procedure for the Workover Rig Instrument Panel Kits for C9, C11, C13, and C15 Engines with TH31 / TH35 and CX31 / CX35 Transmissions in 12 Volt and 24 Volt Applications{7451}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Daily Inspection
2011/10/10 Updated Engine Software Is Now Used for Certain C15 Petroleum Generator Set Engines {1901, 1920}
2011/09/29 A Procedure is Now Used to Install Mounting Blocks for the Auxiliary Lines on Sticks for Certain Excavators {0679, 6502}
Fundamentals of Arc Spray for Reconditioning Components {0679} Fundamentals of Arc Spray for Reconditioning Components {0679}
C3.4B Industrial Engine Balancer
C3.4B Engines For Caterpillar Built Machines Oxygen Sensor
2011/09/28 Installing A New Oil Pan Seal and Mounting Hardware on Certain Trucks Equipped with C11 and C13 Engines {1302, 7553, 7555}
320E and 323E Excavators Machine System Specifications Swing Drive Mounting
Procedure to Replace Torque Converter Lip Seal on CX31 and CX35 On-Highway Transmissions and CX31-P600 and CX35-P800 Petroleum Transmissions{3105, 7555} Procedure to Replace Torque Converter Lip Seal on CX31 and CX35 On-Highway Transmissions and CX31-P600 and CX35-P800 Petroleum Transmissions{3105, 7555}
C3.4B Industrial Engine Plate Locations and Film Locations - Aftertreatment
284-0415 Bulk Fuel Filtration Group 100 GPM Flow Rate{0680, 0782, 1250, 1280} 284-0415 Bulk Fuel Filtration Group 100 GPM Flow Rate{0680, 0782, 1250, 1280}
2011/10/27 New Information Is Now Available for Modifying the Control Panel Remote Start Circuit Wiring of the Crank Rest Time Delay Relay On C280 Marine Engines {1408, 1451, 7451}
2011/11/21 New Clamping for Water Lines on Certain 3600 and C280 Engines {1380}
3512C and 3516C Marine Auxiliary and Generator Set Engines Product Storage
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Electrical Connectors
C32 Auxiliary Engine Cold Weather Operation
C32 Marine Generator Set Overhaul (Top End)
320D and 323D Excavators Machine System Specifications Front Idler
1U-9001 and 1U-9002 Automatic Hone Tooling{0599, 0677, 0738, 7562, 7562} 1U-9001 and 1U-9002 Automatic Hone Tooling{0599, 0677, 0738, 7562, 7562}