Configuration - Check
Use the following steps to verify the configuration parameters and the personalization parameters. Some situations may require variations to the default.
Contact Product Support to discuss any abnormal requirements that you are unsure or unclear about.
- Connect a laptop to the UPS and launch the UPS tuner service tool.
- Verify that Q4S breaker is in the ON (closed) position
- Verify that the UPS Tuner reports the status of the board as "Personalization STATUS 1" for MIZN and CHAN.
- Configure the parameters for the MIZN PCA, CHAN PCA, and the GDEN PCA,
- Run the test for the LED lights to verify that the LED lights will illuminate and cycle through the available color changes twice.
- Verify the correct date and time.
- Close the maintenance bypass switch for the Maintenance Bypass Cabinets (MBC), if available.
- Open the UPS Output isolation switch for the MBC, if available.
Applications that have the 3-CB external maintenance bypass cabinet complete the following steps:
- Open the UPS input isolation switch on the MBC.
- Follow normal operating procedures and continue powering down the UPS system.
- Place the MAINS 1 (Q1) and the MAINS 2 (Q4S) input switches to the OFF (open) position to de-energize the switches
Caterpillar Information System:
UPSB125 Uninterruptible Power Supply UPS Battery - 50Hz Troubleshooting
C9 Industrial Engines Refill Capacities
Vane Type Hydraulic Pump Identification Guidelines {5055} Vane Type Hydraulic Pump Identification Guidelines {5055}
2011/05/25 New Software Is Available for Certain C13 Industrial Engines {1901, 1920}
390F Excavator Machine System Bucket Linkage
C7 Engines for Caterpillar Built Machines Valve Mechanism
C9 Industrial Engines Fuel System - Prime
C9 Industrial Engines Engine Oil and Filter - Change
146-4080 Digital Multimeter Specification, Testing, and Maintenance Manual{0374, 0599, 0709} 146-4080 Digital Multimeter Specification, Testing, and Maintenance Manual{0374, 0599, 0709}
TA19 Transmission Pressure Sensor (Transmission Oil) - Remove and Install
Installation Procedure for 374-5523 Stick Lines Gp on Certain Hydraulic Excavators {5057} Installation Procedure for 374-5523 Stick Lines Gp on Certain Hydraulic Excavators {5057}
UPSB125 Uninterruptible Power Supply UPS Battery - 50Hz IGBT - Test
C7 Engines for Caterpillar Built Machines Camshaft
3500C Marine Engines Fuel Injector Mechanism
C3.4B Engines for Caterpillar Built Machines Turbocharger - Inspect
C3.4B Engines for Caterpillar Built Machines Flywheel - Inspect
C3.4B Engines for Caterpillar Built Machines Flywheel Housing - Inspect
C3.4B Engines for Caterpillar Built Machines V-Belt - Test
C3.4B Engines for Caterpillar Built Machines Fuel System - Prime
C3.4B Engines for Caterpillar Built Machines Piston Height - Inspect
2011/05/12 New Software Is Now Released for Product Link PL522/523 Systems On All Cat Product {7606}
2011/07/18 New Pressure Switch Is Now Used For Air Conditioner Refrigerant On Certain Cat Products {1435, 1809}
2012/01/16 Special Instruction, REHS7131 , "Procedure for the Installation of the 372-1187 Nitrogen Oxide Sensor Gp and the 379-0138 Sensor Kit (NITROGEN OXIDE)" Is Available {1408, 1439, 191N, 7400}
DPF Temperature Sensor Thread Salvage Procedure for Certain C7 thru C15 On-Highway Engines{108F, 1439, 1919, 7400} DPF Temperature Sensor Thread Salvage Procedure for Certain C7 thru C15 On-Highway Engines{108F, 1439, 1919, 7400}