Control (Pedal) - Calibrate
注: 这些步骤为左右电动踏板的典型步骤。
Show/hide table
图 1 | g02291521 |
踏板操纵 (LP) 左电动踏板 (RP) 右电动踏板 |
下述步骤将允许用户使用监视器标定电动踏板。
- 进入维修模式。 输入密码 "9992"。
Show/hide table
图 2 g02291495 - 从 "Calibrations(标定)"菜单选择 "Modulation Inputs(调制输入)"。
Show/hide table
图 3 g02291534 - 选择要标定的电动踏板。
- 按确定键开始标定。
- 确认监视器显示屏上的备注。 按照说明设置测试条件。 按下确定键。
Show/hide table
图 4 g02291536 - 将踏板移到完全向前位置和完全向后位置。 将踏板恢复到空档位置,并按确定键。
注: 使用箭头向下滚动,查看踏板的控制输入信号百分比。
Show/hide table图 5 g02291537 - 如果标定成功且没有错误发生,则显示屏将指示标定完成。
Show/hide table
图 6 g02291553 - 如果出现错误,监视器上将显示 "Error(错误)"。 标定流程将不会保存,并且流程必须重新开始。
使用下述步骤和技术规格确认标定。
- 进入维修模式。 输入密码 "9992"。
Show/hide table
图 7 g02291499 - 从 "Status(状态)"菜单选择 "TCS Operator Input(TCS 操作员输入)"。
Show/hide table
图 8 g02291502 - 向下滚动菜单,查看踏板的状态。
- 确认来自踏板的信号符合表 2 中给出的技术规格。
Show/hide table
踏板标定的确认 - 技术规格 | |
踏板位置 | 档位技术规格 |
空档 | -2% 至 2% |
完全向前 | 98% 到 100% |
完全向后 | -98% 至 100% |
下述步骤将允许用户使用 Cat 电子技师来标定电动踏板。
- 将 Cat 电子技师连接至位于驾驶室左侧座椅后面的诊断接头。
Show/hide table
图 10 g02713758 - 起动 Cat Electronic Technician。
Show/hide table
图 11 g02713761 - 选择"机器控制装置"的 ECM。
Show/hide table
图 12 g02723808 - 从 "Service(维修)"菜单中选择 "Calibrations(标定)"。
Show/hide table
图 13 g02723821 - 突出显示 "Modulation Input Calibrations(调制输入标定)",并点击屏幕左下角的 "Start(开始)"按钮。
Show/hide table
图 14 g02723842 - 选择控制输入以进行标定,并按下 "Begin(开始)"按钮。
Show/hide table
图 15 g02723849 - 按屏幕上的说明去做。 按下 "Next(下一步)"按钮,以继续下一步骤。
- 如果标定成功且没有错误发生,则显示屏将指示标定完成。 按下 "Finish(完成)"按钮,退出或转至下一标定。
- 如果标定失败,将不保存标定。 按下 "Restart(重新开始)"按钮,尝试再次标定,或按下 "Finish(完成)"完成按钮,退出或转至下一标定。
Show/hide table
图 9 | g02713701 |
Cat 电子技师的诊断接头 |
使用下述步骤和技术规格确认标定。
- 从 "Information(信息)"菜单选择 "Status(状态)",或按下工具栏上的 "Status(状态)"按钮。
Show/hide table
图 17 g02723891 - 选择左侧菜单上的 "Tool Control Operator Input Status(机具控制操作员输入状态)",以观察发送至机器 ECM 的踏板信号位置状态。
- 确认来自踏板的信号符合表 2 中给出的技术规格。
Show/hide table
图 16 | g02723878 |
Show/hide table
踏板标定的确认 - 技术规格 | |
踏板位置 | 档位技术规格 |
空档 | -2% 至 2% |
完全向前 | 98% 到 100% |
完全向后 | -98% 至 100% |
Caterpillar Information System:
2010/10/08 Using the Detonation Detection System to Troubleshoot Mechanical Problems in G3600 Engines {1223, 1559}
140 Motor Grader Engine Air Filter Secondary Element - Replace
C9.3 Industrial Engine Valve Mechanism Cover
C3.4B Engines Fuel Contains Water
C13, C15, and C18 Tier 4 Interim Engines ARD Combustion Air - Test
C4.4 Industrial Engine Fuel System - Prime
C3.4B Engines Exhaust Has Excessive White Smoke
C13, C15, and C18 Tier 4 Final Engines Valve Mechanism Cover
2010/12/23 The Air Lines Group between the Turbocharger Compressors and the Aftercoolers Is Improved on G3500C and G3500E Generator Set Engines {1052, 1063, 1071}
C3.4B Engines Engine Vibration Is Excessive
C6.6 Industrial Engine Temperature Sensor (NOx Reduction System)
C6.6 Industrial Engine Pressure Sensor (NOx Reduction System)
C27 and C32 Industrial Engines Cylinder Head - Install
C27 and C32 Industrial Engines Inlet Manifold - Remove and Install
C3.4B Engines Oil Consumption Is Excessive
C3.4B Engines Oil Contains Coolant
C3.4B Engines Oil Pressure Is Low
C3.4B Engines Power Is Intermittently Low or Power Cutout Is Intermittent
C3.4B Engines Valve Lash Is Excessive
C7.1 Engines for Caterpillar Built Machines Belt Tensioner
C6.6 Industrial Engine Fuel Transfer Pump - Electric Transfer Pump
C7.1 Industrial Engine Diesel Particulate Filter Temperature and Pressure Sensor
C7.1 Industrial Engine Diesel Particulate Filter
C9.3 Tier 4 Final Engines Electric Starting Motor