Electric Starting Motor
Show/hide table
Illustration 1 | g02292557 |
When the electric starting motor is viewed from the drive end, the motor rotates in the following direction. ... Clockwise
Specifications
- System voltage ... 24 V
The B+ terminal must be mounted below the horizontal at a maximum angle of ... 60 Degrees
No load performance at
- Speed ... 4060 rpm
- Current ... 142 amp
- Voltage ... 22.5 V
- Current ... 142 amp
Operating temperature range of the starting motor ...
(1) Battery terminal
- Maximum number of cable or wire terminals between the nuts ... 3
- A maximum of two cable terminals can be larger than ... 0 AWG
- Tighten the nut on the battery terminal to the following torque. ...
24 ± 2 N·m (18 ± 1 lb ft) - A maximum of two cable terminals can be larger than ... 0 AWG
(2) Solenoid mounting bolts
- Tighten the nut on the ground terminal to the following torque. ...
8.75 ± 1.05 N·m (77.44 ± 9.29 lb in)
(3) Switch terminal
- Tighten the nut on the switch terminal to the following torque. ...
2.25 ± 0.25 N·m (19.91 ± 2.21 lb in)
(4) Ground terminal
- Tighten the nut on the ground terminal to the following torque. ...
24 ± 2 N·m (18 ± 1 lb ft)
(A) Pinion engaged ...
(B) Pinion disengaged ...
Caterpillar Information System:
C7.1 Industrial Engine Diesel Particulate Filter
C7.1 Industrial Engine Diesel Particulate Filter Temperature and Pressure Sensor
C6.6 Industrial Engine Fuel Transfer Pump - Electric Transfer Pump
C7.1 Engines for Caterpillar Built Machines Belt Tensioner
C3.4B Engines Valve Lash Is Excessive
C3.4B Engines Power Is Intermittently Low or Power Cutout Is Intermittent
C3.4B Engines Oil Pressure Is Low
C3.4B Engines Oil Contains Coolant
C3.4B Engines Oil Consumption Is Excessive
C27 and C32 Industrial Engines Inlet Manifold - Remove and Install
C27 and C32 Industrial Engines Cylinder Head - Install
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Control (Pedal) - Calibrate
C7.1 Industrial Engine Starting the Engine
C6.6 Industrial Engine Fuel Manifold (Rail)
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System One-Way/One or Two Pump - Electric Control: Relief Valve (Line) - Test and Adjust - Tool Relief Valve
C13, C15, and C18 Tier 4 Final Engines Fuel Pressure Regulator
G3520E Generator Set Engines Configuration Parameters
2010/10/20 A New Rocker Shaft Bolt Is Used on Certain C15 and C18 Engines {1102, 7553}
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Medium Pressure: Relief Valve (Main) - Test and Adjust
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Medium Pressure: Relief Valve (Line) - Test and Adjust
C15 and C18 Engines for Caterpillar Built Machines Fuel Priming Pump and Primary Fuel Filter - With Water Separator
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System System Identification
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Work Tool - Select
349F and 352F Excavators Hydraulic System Work Tool Parameter - Program