Crankshaft Front Seal and Wear Sleeve - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
D     | 4C-8982     | 密封安装工具     | 1     |
7F-8022 | 螺栓     | 1     | |
4B-4283 | 垫圈     | 1     | |
E     | 169-5464     | 快速硫化底漆     | -     |
F     | 4C-9507     | 挡圈固定胶     | -     |
注: 承磨衬套和曲轴前密封必须一起安装。
- 将清洁的发动机机油涂覆在密封唇和承磨衬套 (2) 的外径上。 将曲轴前密封安装在承磨衬套上,使密封唇朝向承磨衬套内径有斜面的一侧,如图所示。
Show/hide table
图 1 | g01952094 |
- 使用工具 (E) 除去承磨衬套内径 (X) 和曲轴表面 (Y) 上的所有机油。
Show/hide table
图 2 | g01952096 |
- 将工具 (F) 涂覆在表面 (X) 和 (Y) 上。
- 将曲轴前密封和承磨衬套安装在曲轴上,使密封唇朝向发动机,如图所示。
- 安装工具 (D) ,如图所示。 在螺栓头和安装工具之间涂抹润滑剂。
- 使用工具 (D) 将曲轴前密封和承磨衬套推到曲轴上。 推动安装工具直到安装工具紧靠曲轴末端。 承磨衬套和曲轴前密封此时处于正确位置。
- 拆下工具 (D) 。
End By: 安装减振器和皮带轮。
Caterpillar Information System:
C15 and C18 Industrial Engines Inlet and Exhaust Valves - Remove and Install
G3304B and G3306B Engines Crankshaft Front Seal and Wear Sleeve - Remove
C15 and C18 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
G3304B and G3306B Engines Water Directors - Remove and Install
C9.3 Marine Propulsion Engine Decommissioning and Disposal
C13 Tier 4 Final Engines Electronic Unit Injector Mechanism
G3304B and G3306B Engines Flywheel Housing - Install
C13, C15, and C18 Tier 4 Interim Engines ARD Is Disabled
797F and 797F XQ Off-Highway Truck Power Train Transmission Hydraulic Control
C175-16 Locomotive Engine Engine Governing - Adjust
G3304B and G3306B Engines Flywheel Housing - Remove
G3512E and G3520E Generator Set Engines Electronic Control System Parameters
793F Off-Highway Truck Machine Systems Seat - Remove and Install
C13 Engines for Caterpillar Built Machines Electronic Unit Injector Rocker Arm
797F and 797F XQ Off-Highway Truck Hydraulic System Truck Body Mounting
C7.1 Industrial Engine Gauges and Indicators
793F Off-Highway Truck Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install
C175-16 and C175-20 Generator Set Engines Fuel System Operation
793F Off-Highway Truck Engine Supplement Fuel Filter (Secondary) and Fuel Filter Base - Remove and Install
C7.1 Industrial Engine and Generator Set Throttle Setup
G3304B and G3306B Engines Crankshaft Rear Seal and Wear Sleeve - Remove
G3304B and G3306B Engines Crankshaft Rear Seal and Wear Sleeve - Install
C15 and C18 Industrial Engines Camshaft Gear - Remove and Install
C13 Tier 4 Final Engines Rocker Shaft