Prelubrication Oil Pump - Remove and Install
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Disconnect the batteries. Refer to Operation and Maintenance Manual, "Engine Oil Change".
Show/hide table
Illustration 1 g01688675 - Put an index mark on the harness assemblies that are connected to prelubrication oil pump (1).
- Disconnect the harness assemblies from prelubrication oil pump (1).
- Disconnect the tube assemblies from inlet port (4) and outlet port (5) from prelubrication oil pump (1).
- The weight of prelubrication oil pump (1) is approximately
20 kg (43 lb) . - Remove bolts (3) and spacers (2) and remove prelubrication oil pump (1).
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- The weight of prelubrication oil pump (1) is approximately
20 kg (43 lb) . - Position prelubrication oil pump (1) and install spacers (2) and bolts (3).
- Connect the tube assemblies to inlet port (4) and outlet port (5) on prelubrication oil pump (1).
- Connect the harness assemblies to prelubrication oil pump (1) .
- Connect the batteries. Refer to Operation and Maintenance Manual, "Engine Oil Change".
Show/hide table
| |
| Illustration 2 | g01688675 |
Caterpillar Information System:
G3516 Petroleum Engines Thermostatic Valve - Install
G3516 Petroleum Engines Thermostatic Valve - Remove
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Turbocharger - Install
C18 Fire Pump Industrial Engine Vibration Damper and Pulley - Remove and Install
C18 Fire Pump Industrial Engine Flywheel - Install - Adapter
TH31-E61 and TH35-E81 Petroleum Transmissions Safety Messages
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Turbocharger - Remove
C175-16 Petroleum Generator Set Engines Safety Messages
Updating Engines that are Equipped with a Heated Nozzle for the Caterpillar Regeneration System (CRS){108B, 108E, 108M} Updating Engines that are Equipped with a Heated Nozzle for the Caterpillar Regeneration System (CRS){108B, 108E, 108M}
C18 Fire Pump Industrial Engine Flywheel - Remove - Adapter
C18 Fire Pump Industrial Engine Engine Support (Front) - Remove and Install
C18 Fire Pump Industrial Engine Water Temperature Regulator Housing - Remove and Install
2008/10/20 Glow Plugs {1412}
Procedure to Update the Open Crankcase Ventilation System on C13 and C15 Engines{1074, 1120, 1317} Procedure to Update the Open Crankcase Ventilation System on C13 and C15 Engines{1074, 1120, 1317}
R250 Automatic Voltage Regulator Load Acceptance Module - Adjust
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Engine Oil Pan - Remove
Updating the Certification Label for China{7557} Updating the Certification Label for China{7557}
G3516 Petroleum Engines Engine Oil Pan - Disassemble
G3516 Petroleum Engines Engine Oil Pan - Assemble
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Engine Oil Pan - Install
2008/10/20 EERP1000 Support CD for the PL1000E and PL1000T {7606, 7620}
TH55FT-E70 and TH55FT-E90 Transmissions Lifting and Tying Down the Transmission
G3516 Petroleum Engines Vibration Damper - Remove and Install
3500B Generator Sets Safety Messages