Flywheel - Install - Adapter
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7575     | Lifting Bracket     | 2     |
B     | -     | Guide Stud 5/8 - 18 by 8 inch     |
2     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Raise the temperature of ring gear (4). Install ring gear (4) on flywheel (3) .
Show/hide table
Illustration 1 | g01686653 |
Note: Ring gear (4) must be installed with the chamfered side of the teeth upward. The chamfered side of the gear teeth will be facing toward the starting motor when the flywheel is installed.
- Install Tooling (B) in the crankshaft.
Show/hide table
Illustration 2 | g01683693 |
- Install Tooling (A) and a suitable lifting device on flywheel (3). The weight of flywheel (3) is approximately 120 kg (265 lb). Position the flywheel on the crankshaft.
- Position adapter (2) on the flywheel.
- Apply clean engine oil to the threads of bolts (1) .
- Install bolts (1). Remove Tooling (B). Install bolts (1) in place of Tooling (B) .
- Tighten bolts (1) to a torque of 270 ± 40 N·m (200 ± 30 lb ft).
- Remove Tooling (A) from the flywheel.
- Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect".
Caterpillar Information System:
TH31-E61 and TH35-E81 Petroleum Transmissions Safety Messages
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Turbocharger - Remove
C175-16 Petroleum Generator Set Engines Safety Messages
Updating Engines that are Equipped with a Heated Nozzle for the Caterpillar Regeneration System (CRS){108B, 108E, 108M} Updating Engines that are Equipped with a Heated Nozzle for the Caterpillar Regeneration System (CRS){108B, 108E, 108M}
C18 Fire Pump Industrial Engine Flywheel - Remove - Adapter
C18 Fire Pump Industrial Engine Engine Support (Front) - Remove and Install
C18 Fire Pump Industrial Engine Water Temperature Regulator Housing - Remove and Install
R250 Automatic Voltage Regulator Knee Frequency - Adjust - For Constant Volts Per Hertz Operation
C175-16 Petroleum Generator Set Engines Engine Oil and Filter - Change
R250 Automatic Voltage Regulator Wiring Diagram
C18 Fire Pump Industrial Engine Water Pump - Install
R250 Automatic Voltage Regulator Load Acceptance Module Operation
C18 Fire Pump Industrial Engine Vibration Damper and Pulley - Remove and Install
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Turbocharger - Install
G3516 Petroleum Engines Thermostatic Valve - Remove
G3516 Petroleum Engines Thermostatic Valve - Install
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Prelubrication Oil Pump - Remove and Install
2008/10/20 Glow Plugs {1412}
Procedure to Update the Open Crankcase Ventilation System on C13 and C15 Engines{1074, 1120, 1317} Procedure to Update the Open Crankcase Ventilation System on C13 and C15 Engines{1074, 1120, 1317}
R250 Automatic Voltage Regulator Load Acceptance Module - Adjust
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Engine Oil Pan - Remove
Updating the Certification Label for China{7557} Updating the Certification Label for China{7557}
G3516 Petroleum Engines Engine Oil Pan - Disassemble
G3516 Petroleum Engines Engine Oil Pan - Assemble