Vibration Damper and Pulley - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | -     | Guide Stud (5/8 - 18 x 9 inch)     |
2     |
Start By:
- Remove the alternator drive belt. Refer to Disassembly and Assembly, "Alternator - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove two bolts (3) and install Tooling (A) .
Show/hide table
Illustration 1 | g01686873 |
- Remove remaining bolts (3). Remove pulley (1) from vibration damper assembly (2) .
- Use two people in order to remove vibration damper assembly (2). The weight of vibration damper assembly (2) is approximately 46 kg (100 lb).
- Remove bolts (7) and remove spacer (6) .
Show/hide table
Illustration 2 | g01691875 |
- separate damper (5) from adapter (4) .
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | -     | Guide Stud (5/8 - 18 x 9 inch)     |
2     |
B     | 4C-5593     | Anti-Seize Compound     | -     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Thoroughly inspect the viscous damper for signs of leakage or for signs of a dented (damaged) case. Either of these conditions can cause the weight to make contact with the case. This can affect the viscous damper's operation. |
- Position damper (5) on adapter (4) .
Show/hide table
Illustration 3 | g01691875 |
- Position spacer (6) and install bolts (7) .
- Install Tooling (A) in the crankshaft.
Show/hide table
Illustration 4 | g01686873 |
- Install vibration damper assembly (2) on Tooling (A) .
- Install pulley (1) on Tooling (A) .
- Apply Tooling (B) to bolts (3) .
- Remove Tooling (A) and install the remaining bolts.
End By: Install the alternator drive belt. Refer to Disassembly and Assembly, "Alternator - Remove and Install".
Caterpillar Information System:
C18 Fire Pump Industrial Engine Flywheel - Install - Adapter
TH31-E61 and TH35-E81 Petroleum Transmissions Safety Messages
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Turbocharger - Remove
C175-16 Petroleum Generator Set Engines Safety Messages
Updating Engines that are Equipped with a Heated Nozzle for the Caterpillar Regeneration System (CRS){108B, 108E, 108M} Updating Engines that are Equipped with a Heated Nozzle for the Caterpillar Regeneration System (CRS){108B, 108E, 108M}
C18 Fire Pump Industrial Engine Flywheel - Remove - Adapter
C18 Fire Pump Industrial Engine Engine Support (Front) - Remove and Install
C18 Fire Pump Industrial Engine Water Temperature Regulator Housing - Remove and Install
R250 Automatic Voltage Regulator Knee Frequency - Adjust - For Constant Volts Per Hertz Operation
C175-16 Petroleum Generator Set Engines Engine Oil and Filter - Change
R250 Automatic Voltage Regulator Wiring Diagram
C18 Fire Pump Industrial Engine Water Pump - Install
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Turbocharger - Install
G3516 Petroleum Engines Thermostatic Valve - Remove
G3516 Petroleum Engines Thermostatic Valve - Install
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Prelubrication Oil Pump - Remove and Install
2008/10/20 Glow Plugs {1412}
Procedure to Update the Open Crankcase Ventilation System on C13 and C15 Engines{1074, 1120, 1317} Procedure to Update the Open Crankcase Ventilation System on C13 and C15 Engines{1074, 1120, 1317}
R250 Automatic Voltage Regulator Load Acceptance Module - Adjust
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Engine Oil Pan - Remove
Updating the Certification Label for China{7557} Updating the Certification Label for China{7557}
G3516 Petroleum Engines Engine Oil Pan - Disassemble
G3516 Petroleum Engines Engine Oil Pan - Assemble
G3508B, G3512B, G3512B, G3516B and G3520B Petroleum Engines Engine Oil Pan - Install