Engine Oil Cooler Bypass and Cooling Jet Sequence Valves
Show/hide table
| |
| 图 1 | g03835221 |
|
右视图 | |
Show/hide table
| 技术规格 - 262-7578 发动机油管路总成 | |||
|---|---|---|---|
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | 4 | 109-2332 O 形密封圈 | 组装前，用密封的液体稍稍润滑孔。 |
| 2 | 8 | 0S-1594 螺栓 | 采用以下步骤紧固卡箍组件的螺栓： 1. 拧紧卡箍组件，直到卡箍组件配合到管上。 2. 将卡箍组件拧紧到接头上。 3. 将卡箍组件拧紧到管上。 |
| 3 | 8 | 0S-1571 螺栓 | |
| 4 | 2 | 7N-7697 柱塞 | 冷却喷嘴管顺序阀必须在 冷却喷嘴管顺序阀必须在 |
| 5 | 2 | 6B-9202 弹簧 | 测试力下的长度为 |
| 测试力为 |
|||
| 测试后的自由长度为 |
|||
| 6 | 2 | 237-7623 O 形密封圈 | 组装前，用密封的液体稍稍润滑孔。 |
| 7 | 1 | 1P-1367 柱塞 | 发动机机油滤清器旁通阀的柱塞必须在孔中自由移动。
发动机运转期间，发动机机油滤清器旁通阀必须在 |
| 8 | 3 | 7G-6713 弹簧 | 测试力下的长度为 |
| 测试力为 |
|||
| 测试后的自由长度约为 |
|||
Show/hide table
| |
| 图 2 | g03835222 |
|
前视图 | |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
|---|---|---|---|
| 9 | 1 | 2W-1053 塞 | 拧紧至扭矩为 |
| 10 | 1 | 2W-1969 旁通阀 | 机油冷却器旁通阀必须在 |
| 11 | 1 | 2W-1635 弹簧 | 测试力下的长度为 |
| 测试力为 |
|||
| 测试后的自由长度为 |
Caterpillar Information System:
C175-16 and C175-20 Generator Set Engines Oil Contains Fuel
3500B Locomotive Engines Configuration Parameters
C4.4 Industrial Engine Engine Rating Conditions
C4.4 Industrial Engine Engine Rating Definitions
3500C Marine Engines Camshaft
C18 Industrial Engines Monitoring System
793F and 793F XQ Off-Highway Truck Fast Fill Service System General Information
345D, 349D and 349D2 Excavators Hydraulic System Swing Hydraulic System
Repairing the Fuel Injector Rocker Arm{1102, 1123, 1290} Repairing the Fuel Injector Rocker Arm{1102, 1123, 1290}
2008/04/01 A New Valve Cover is Used {1100, 1120}
345D, 349D and 349D2 Excavators Hydraulic System Bucket Hydraulic System
345D, 349D and 349D2 Excavators Hydraulic System Control Valve (Stick Lowering)
C175-16 and C175-20 Engines for Off-Highway Trucks Camshaft
C175-16 and C175-20 Generator Set Engines Crankcase Pressure Is High
C18 Marine and Marine Generator Set Engines Turbocharger
345D, 349D and 349D2 Excavators Hydraulic System Oil Makeup (Swing System)
2008/02/25 A New Oil Filter Group is Now Used on the TH48-E80 Oil/Gas Transmission {3030, 3067}
345D, 349D and 349D2 Excavators Hydraulic System Relief Valve (Cushion Crossover) - Anti-Reaction Valves
2008/06/02 An Improved Alternator Belt Guard Is Now Used {7174}
345D, 349D and 349D2 Excavators Hydraulic System Solenoid Valve (Fine Swing) - If Equipped
3176C, 3406E and 3456 Industrial Engines ECM Software - Install
3176C, 3406E and 3456 Industrial Engines Intake Manifold Air Pressure Is High
345D, 349D and 349D2 Excavators Hydraulic System Travel Hydraulic System
SR5 Electric Power Generation Bus Bar - Remove and Install