Coolant Temperature Sensor - Remove and Install
- Drain the coolant into a suitable container for storage or for disposal. Drain the coolant to a level that is below the coolant temperature sensor. Refer to Operation and maintenance Manual, "Cooling System Coolant (ELC) - Change".
Show/hide table
Illustration 1 g01437341 - Disconnect harness assembly (1) from coolant temperature sensor (2).
- Remove coolant temperature sensor (2) from the engine.
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Install the O-ring seal onto coolant temperature sensor (2).
- Install coolant temperature sensor (2) into the engine. Tighten coolant temperature sensor (2) to a torque of
20 ± 3 N·m (15 ± 2 lb ft) . - Connect harness assembly (1) onto coolant temperature sensor (2).
- Fill the cooling system. Refer to Operation and maintenance Manual, "Cooling System Coolant (ELC) - Change".
Show/hide table
Illustration 2 | g01437341 |
Note: Check the O-ring seal for wear or for damage. If necessary, replace the O-ring seal.
Caterpillar Information System:
C27 and C32 Engines for Caterpillar Built Machines Electronic Service Tool Does Not Communicate
C9 Petroleum Engines Atmospheric Pressure Sensor - Remove and Install
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0268 - FMI 02
C13 and C15 On-highway Engines Engine Monitoring System
C175-16 Locomotive Engine Water Pump
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0190 - FMI 03
G3500 A3 Engines Exhaust Temperature Module
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Hydraulic Control - Assemble
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Hydraulic Control - Disassemble
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Hydraulic Control - Install
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Hydraulic Control - Remove
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0190 - FMI 02
C9 Petroleum Engines Engine Oil Pressure Sensor - Remove and Install
3176C, 3406E and 3456 Industrial Engines Electrical Connectors
2007/12/17 The Caterpillar Digital Voltage Regulator (CDVR) Has been Improved {4467}
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0269 - FMI 04
C9 Petroleum Engines Fuel Pressure Sensor - Remove and Install
C13 and C15 On-highway Engines Solenoid Valve - Test
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0333 - FMI 03
C9 Petroleum Engines Injection Actuation Pressure Sensor - Remove and Install
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0333 - FMI 04
C9 Petroleum Engines Speed/Timing Sensor - Remove and Install
C9 Petroleum Engines Turbocharger Outlet Pressure Sensor - Remove and Install
C9 Petroleum Engines Inlet Air Temperature Sensor - Remove and Install