Transmission Hydraulic Control - Disassemble
拆解步骤
Show/hide table
需要的工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 6V-5219     | 螺栓     | 2     |
B     | 1P-1853     | 挡圈钳     | 1     |
开始:
- 拆下变速箱液压控制装置。 请参阅拆解和组装, "变速箱液压控制装置 - 拆卸"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 拆下螺栓 (1) 。 拆下安全阀 (2) 。
Show/hide table
图 1 | g01437283 |
- 拆下螺塞 (3) 和 O 形密封圈。 拆下螺栓 (4) 。 拆下盖 (5) 和 O 形密封圈。
Show/hide table
图 2 | g01437287 |
- 安装工具 (A) 。 拆下螺钉 (7) 。 均匀地拆下螺栓 (6) ,直至盖 (8) 接触到工具 (A) 。 拆下螺栓 (6) 。 松开工具 (A) ,直至释放所有的弹簧张力。 拆下工具 (A) 。
Show/hide table
图 3 | g01437295 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 拆下负载活塞 (11) 、弹簧 (10) 和滑阀组件 (9) 。
Show/hide table
图 4 | g01437300 |
- 从滑阀组件 (9) 上拆下缓动阀 (12) 。
Show/hide table
图 5 | g01437302 |
- 使用工具 (B) 拆下挡圈 (16) 。 从滑阀组件 (9) 上拆下挡板 (15) 、弹簧 (14) 和钢珠球 (13) 。
Show/hide table
图 6 | g01437303 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 从调节阀 (20) 上拆下接头 (17) 。 拆下螺母 (24) 、垫圈 (19) 和电磁阀 (23) 。
Show/hide table
图 7 | g01437332 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 如果需要清洁调节阀 (20) ,使用下列步骤:
- 从阀芯 (22) 上拆下 O 形密封圈。 缓慢地拆下阀芯 (22) ,以释放弹簧 (18) 上的张力。
- 拆下滑阀 (21) 和弹簧 (18) 。
- 拆下螺栓 (25) 和盖 (26) 。 拆下排放装置 (27) ,拆下温度传感器 (28) 。
Show/hide table
图 8 | g01437322 |
- 拆下螺塞 (29) 和 O 形密封圈。 拆下螺栓 (30) 和板 (31) 。
Caterpillar Information System:
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Hydraulic Control - Install
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Hydraulic Control - Remove
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0190 - FMI 02
2007/12/01 Procedure to Use the Correct Mounting Bolts with the 10R-2356 Flywheel As {1156}
2007/12/24 Procedure to Use the Correct Mounting Bolts with the 10R-2356 Flywheel As {1156}
2011/02/11 Procedure to Use the Correct Mounting Bolts with the 10R-2356 Flywheel As {1156}
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0111 - FMI 03
2008/01/01 A New O-ring for the Injector Sleeve is Now Used {1100}
2008/01/07 A New O-ring for the Injector Sleeve is Now Used {1100}
C175 Generator Sets Fuel Related Components in Cold Weather
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Indicators of Alarm Module or Remote Annunciator Are Constantly Flashing
G3600 Engines Starting - Test
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Hydraulic Control - Assemble
G3500 A3 Engines Exhaust Temperature Module
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0190 - FMI 03
C175-16 Locomotive Engine Water Pump
C13 and C15 On-highway Engines Engine Monitoring System
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0268 - FMI 02
C9 Petroleum Engines Atmospheric Pressure Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Electronic Service Tool Does Not Communicate
C9 Petroleum Engines Coolant Temperature Sensor - Remove and Install
C9 Petroleum Engines Engine Oil Pressure Sensor - Remove and Install
3176C, 3406E and 3456 Industrial Engines Electrical Connectors
2007/12/17 The Caterpillar Digital Voltage Regulator (CDVR) Has been Improved {4467}