Transmission Hydraulic Control - Assemble
组装步骤
Show/hide table
需要的工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 6V-5219     | 螺栓     | 2     |
B     | 1P-1853     | 挡圈钳     | 1     |
- 定位板 (31) 。 安装螺栓 (30) 。
Show/hide table
图 1 | g01437493 |
- 定位盖 (26) 并安装螺栓 (25) 。
- 在要密封的 O 形密封圈上涂抹润滑剂。 将 O 形密封圈装在螺塞 (29) 上。 安装螺塞 (29) 。拧紧螺塞 (29) 至扭矩 45 ± 7.5 N·m (33 ± 5.5 lb ft)
- 安装排放装置 (27) 。 拧紧排放装置 (27) 至扭矩 35 ± 7.5 N·m (26 ± 5.5 lb ft)。
- 安装温度传感器 (20) 。
- 如果需要解体清洁调节阀 (20) ,使用下列步骤:
- 安装弹簧 (18) 并安装滑阀 (21) 。
- 在要密封的 O 形密封圈上涂抹润滑剂。 将 O 形密封圈装在阀芯 (22) 上。 安装阀芯 (22) 。 拧紧阀芯 (22) 至扭矩 50 ± 5 N·m (37 ± 4 lb ft)。
Show/hide table
图 2 | g01437332 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 安装电磁阀 (23) 并安装垫圈 (19) 。 安装螺母 (24) 。 拧紧螺母 (24) 至扭矩 13 ± 1.5 N·m (10 ± 1.1 lb ft)。
- 将接头 (17) 装入调节阀 (20) 。 拧紧接头 (17) 至扭矩14 ± 4 N·m (10 ± 3 lb ft)。
- 将钢珠球 (13) 、弹簧 (14) 和挡板 (15) 装入滑阀组件 (9) 。 使用工具 (B) 安装挡圈 (16) 。
Show/hide table
图 3 | g01437303 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 将缓动阀 (12) 装入滑阀组件 (9) 。
Show/hide table
图 4 | g01437302 |
- 安装滑阀组件 (9) 、弹簧 (10) 和负载活塞 (11) 。
Show/hide table
图 5 | g01437300 |
- 定位盖 (8) 。 安装工具 (A) 。 均匀地安装螺栓 (6) ,直至盖 (8) 完全落座。 安装螺钉 (7) 。 拆下工具 (A) 。
Show/hide table
图 6 | g01437295 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 将 O 形密封圈装入盖 (5) 。 定位盖 (5) 并安装螺栓 (4) 。 将 O 形密封圈装在螺塞 (3) 上并安装螺塞 (3) 。
Show/hide table
图 7 | g01437287 |
- 定位安全阀 (2) ,然后安装螺栓 (1) 。
Show/hide table
图 8 | g01437283 |
End By: 安装变速箱液压控制装置。 请参阅 拆解和组装, "变速箱液压控制装置 - 安装"。
Caterpillar Information System:
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Hydraulic Control - Disassemble
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Hydraulic Control - Install
TH55-E70 and TH55-E90 Petroleum Transmissions Transmission Hydraulic Control - Remove
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0190 - FMI 02
2007/12/01 Procedure to Use the Correct Mounting Bolts with the 10R-2356 Flywheel As {1156}
2007/12/24 Procedure to Use the Correct Mounting Bolts with the 10R-2356 Flywheel As {1156}
2011/02/11 Procedure to Use the Correct Mounting Bolts with the 10R-2356 Flywheel As {1156}
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0111 - FMI 03
2008/01/01 A New O-ring for the Injector Sleeve is Now Used {1100}
2008/01/07 A New O-ring for the Injector Sleeve is Now Used {1100}
C175 Generator Sets Fuel Related Components in Cold Weather
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Indicators of Alarm Module or Remote Annunciator Are Constantly Flashing
G3500 A3 Engines Exhaust Temperature Module
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0190 - FMI 03
C175-16 Locomotive Engine Water Pump
C13 and C15 On-highway Engines Engine Monitoring System
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0268 - FMI 02
C9 Petroleum Engines Atmospheric Pressure Sensor - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Electronic Service Tool Does Not Communicate
C9 Petroleum Engines Coolant Temperature Sensor - Remove and Install
C9 Petroleum Engines Engine Oil Pressure Sensor - Remove and Install
3176C, 3406E and 3456 Industrial Engines Electrical Connectors
2007/12/17 The Caterpillar Digital Voltage Regulator (CDVR) Has been Improved {4467}
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0269 - FMI 04