Intake Manifold Air Temperature Is High
采用此步骤以对进气温度偏高进行故障诊断与排除。 如果下列事件代码激活,采用此步骤。 有关事件代码和这些代码的默认触发点的信息,请参阅故障诊断与排除, "事件代码"。 必须进入 Caterpillar 电子技师(ET)的监控系统才能查看这些代码的当前触发点。
Show/hide table
事件代码     | ||
---|---|---|
代码和描述     | 产生此代码的状况     | 系统响应     |
105-0 进气歧管温度高(警告)     | 在延迟时间内进气歧管空气温度高于触发点。     | 记录该代码。 诊断灯将闪烁。 报警灯将发光。     |
可能原因
- 冷却液温度高
- 环境空气温度高
- 进气阻力
- 排气阻力
- 海拔高度
- 发动机过载
建议的措施
冷却液温度高
高冷却液温度将提高进气歧管空气温度。
确认冷却系统已加注到正确液位。 如果冷却液液位过低,空气就会进入冷却系统中。 冷却系统混入空气会造成冷却液流降低。
检查冷却风扇的运转。 风扇如果没有以正确的转速运转可能造成流过后冷器芯的空气速度不当。 后冷器芯缺乏适当气流流过时可造成进气无法冷却至正常温度。
检查冷却系统中有无空气。 空气可以通过不同渠道进入冷却系统。 冷却系统中有空气的最常见的起因是没有正确加注冷却系统和燃烧气体漏进冷却系统。 燃烧气体可能通过内部裂纹、损坏的缸盖或缸盖衬垫进入冷却系统。
环境空气温度高
确定环境空气温度是否在冷却系统设计的技术规格范围内。 当环境温度对于冷却系统的额定值而言过高时,在环境空气与冷却液温度之间就没有足够的温差。
进气阻力
检查进气系统中有无阻塞。 发动机的进气受阻会导致气缸温度过高。 气缸温度过高会导致冷却系统温度高于正常值。 冷却液温度必须在正确的范围内才能冷却进气。
排气阻力
检查排气系统有无阻力。 发动机的排气受阻会导致气缸温度高。
海拔高度
考虑高海拔工作。 高海拔工作时会降低冷却系统的冷却能力。 必须使用一个足够大的加压系统以防冷却液沸腾。 确保发动机的设置适合于海拔高度。
发动机过载
发动机可能会在拖动工况下运转。 施加到发动机上的负载过大时,发动机就会在拖动工况下运转。 发动机在拖动工况下运转时,发动机转速不随油量的增加而提高。 这一相对较低的发动机转速同时也造成流经冷却系统的冷却液流量的降低。
如果怀疑传感器电路存在电气故障,请参阅故障诊断与排除, "传感器信号(模拟、有源)- 测试"。
Caterpillar Information System:
3608 Engine Governor Drive - Assemble - Earlier
3176C, 3406E and 3456 Industrial Engines Fuel Temperature Is High
3176C, 3406E and 3456 Industrial Engines Fuel Pressure Problem
G3500 Engines Nitrogen Oxide Sensor - Calibrate
C15 and C18 Petroleum Engines Engine Design
C15 and C18 Petroleum Engines Turbocharger Oil Lines
G3500B Engines Nitrogen Oxide Sensor - Calibrate
Manual Programming of a UPS System{4480, 7620} Manual Programming of a UPS System{4480, 7620}
Procedure for Using the Automatic Flash Update Tool for a UPS System{4480, 7620} Procedure for Using the Automatic Flash Update Tool for a UPS System{4480, 7620}
G3520C and G3520E Engines Turbocharger
Procedure to Relocate the Inlet Hose for the ARD Purge Air Pump{107P, 1803} Procedure to Relocate the Inlet Hose for the ARD Purge Air Pump{107P, 1803}
C15 and C18 Petroleum Engines Turbocharger Oil Lines
3608 Engine Fuel Transfer Pump - Assemble
3176C, 3406E and 3456 Industrial Engines Oil Pressure Is Low
2007/12/03 Cylinder Head Gasket {1100, 1251}
3608 Engine Valve Lifter - Install
2008/12/08 Procedure for Cleaning the Power Train {3065, 3139}
3176C, 3406E and 3456 Industrial Engines Electrical Power Supply - Test
3608 Engine Air Starting Motor - Remove
3608 Engine Water Pump - Disassemble
3608 Engine Auxiliary Water Pump - Remove
3608 Engine Auxiliary Water Pump - Disassemble
2008/01/01 Use the Correct Fittings for the Fuel Manifold {1274, 1380}
3608 Engine Fuel Transfer Pump - Remove